Mychef Bake Technical & Service Manual Download Page 22 | Manualshive

Page: 22 / 71

background image

mychefcooking.com

TECHNICAL SUPPORT SERVICE MANUAL iCOOK | iBAKE | COOK | BAKE | SNACK | BAKERSHOP - DT.MS.CB.2202.2

22

Power contactor

2.3.4.

The oven turns itself off or the electronics do not respond

Check if the safety thermostat has tripped. If the oven turns off because the safety thermostat
has tripped, check if the temperature inside the chamber is over 350ºC. If the thermostat
trips before, change the safety thermostat. If it trips at over 350ºC, the problem may be a
contactor or the control plate not regulating the temperature correctly.

If the oven turns off and it is not because the safety thermostat has tripped, the problem will
be the temperature on the control or relay board. To check the temperature on the control
board, with the oven on, press the time button for a few seconds. To check the temperature
on the relay board, with the oven on, press the fan button for a few seconds. Check that
these temperatures are below 80°C.

«
...
20
21
22
23
24
...
»

Summary of Contents for Bake








































































Reviews:

No comments

Related manuals for Bake

Brand: R.G.V. Pages: 24

Brand: K-FEE Pages: 9

Brand: MACAP Pages: 40

Brand: Dash Pages: 17

Brand: T-Fal Pages: 98

the Perfect Press SSG600BSS4EEU1

Brand: Sage Pages: 69

Brand: Waring Pages: 44

Brand: EDM Product Pages: 21

Brand: Parkinson Cowan Pages: 52

Brand: Galaxy Equipment Pages: 4

Brand: BRAYER Pages: 44

Brand: SIMPLETaste Pages: 18

Brand: miniland baby Pages: 2

Flush Mount Trim

Brand: Viking Pages: 4

Cheese Blocker 1837

Brand: Vollrath Pages: 12

Brand: CONTINENTAL EDISON Pages: 16

Brand: CONTINENTAL EDISON Pages: 44

Brand: Jula Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands