Mychef Bake Technical & Service Manual Download Page 31

Page: 31 / 71

mychefcooking.com

to adapt the electronics to all potential equipment configurations. Some records also allow
to perform tests to verify that all components are working properly.

Password

Password

This field is reserved for future use. Currently it is not necessary to enter the password to
modify configuration parameters.

Type

Record 1 allows you to select the type of oven. Below is a list of all the ovens and the value
assigned to each of them in this field:

NO.

MODEL

MODE

TYPE_MYCHEF_COOK_BAKE_PRO

Mychef Cook Pro or Bake Pro

TYPE_MYCHEF_BAKERSHOP

Mychef Bakershop or Snack

TYPE_MYCHEF_COOK_NOMYCARE

Mychef Cook Up

Reserved

TYPE_MYCHEF_COOK_MASTER

Mychef Cook Master or Bake Master

TYPE_AIR

Mychef Bakershop and Snack AIR

TYPE_AIR_S

Mychef Bakershop and Snack AIR-S

Reserved

TYPE_DEMO

Demo. Disables fan and resistor.

TYPE_TST

Test

TYPE_MAX

Reserved

Tabla 3.

Oven types

By editing this value, it is possible to configure the control board for each type of oven.

TSC Mode

Record 2 sets the number of TSC channels activated. By editing it we can configure the
control board for an oven with or without TSC.

For ovens without TSC this value must always be 0.

For electric ovens with TSC this value must always be 2.

Summary of Contents for Bake








































































Search results

Summary of Contents for Bake

Reviews:

Related manuals for Bake

Brands by name

Popular brands

Mychef Bake, Technical & Service Manual

Search results

Summary of Contents for Bake

Reviews:

Related manuals for Bake

Brands by name

Popular brands