MUTOH VJ-628 ValueJet Operation Manual Download Page 31

Page: 31 / 80

Forwarding/rewinding media from printer driver/VSM 31

Forwarding/Rewinding media

Forwarding/rewinding media from printer driver/VSM

[1]

Display the Printing Preferences screen of printer driver.

"Displaying the Printing Preferences screen of printer driver" on page 8

[2]

Click [Media Feed] in the [Printer Control] under the [Utility] tab.

• The remote panel of VSM launches.

Note

VSM can be launched directly.

"Launching VSM" on page 9

[3]

Enter [Feed Amount].

• The unit of [Feed Amount] can be selected from [mm] and [inch].
• The media is forwarded/rewound by the entered length in the [Feed Amount].

[4]

When [Forward Feed]/ [Backward Feed] is clicked, the media is forwarded/rewound.

• Click [Stop] during forwarding/rewinding to stop the operation.
• Or short press the operation key on the operation panel to stop the operation.

Forwarding/Rewinding media

Summary of Contents for VJ-628 ValueJet

















































































Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands

MUTOH VJ-628 ValueJet, Operation Manual

Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands