manualshive.com logo in svg

MUTOH VJ-628 ValueJet, Operation Manual

Share
Download
MUTOH VJ-628 ValueJet Operation Manual Download Page 12

12     Conditions of usable media

Roll media can be used in this product.

• Please use recommended media. Contact the sales store for recommended media.
• Be cautious of expansion and contraction of media from temperature and humidity.

After opening an unopened media, leave the media for approximately 30 minutes to adjust to environments.

• Do not use media with folds, scratches, tears, curvatures, winding curl and weaving.
• Do not leave a roll media set in this product for a long time. The media can be curled becoming unsuitable for printing.

When not using for a long time, remove a roll media and store in its original package box.

Conditions of usable media

Usable size

Maximum 

width

630mm (If paper tube > media width, then 

paper tube width)

Maximum 

thickness

Head height when Low

0.3mm

Head height when High

1.3mm

Roll outer 

diameter

150mm

Paper tube 

diameter

2 or 3 inches

Weight

9 kg or less

Cautions when handling media

Summary of Contents for VJ-628 ValueJet

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands