MUTOH VJ-628 ValueJet Operation Manual Download Page 22

Page: 22 / 80

22 Correcting paper feed

For the following cases, please conduct this adjustment.

• Using this product for the first time.
• Changing a media type.

For any other cases, please proceed to

"Nozzle check and cleaning" on page 27

A ruler is used for this adjustment. Please prepare a commercially available ruler.

Correcting paper feed

Note

When the following defects are found in printing results, they may improve by conducting a paper feed correction.

• Images are overlapping.
• There are white lines in images.

Paper feed correction steps

Initial adjustment

[1]

Display the Printing Preferences screen of printer driver.

"Displaying the Printing Preferences screen of printer driver" on page 8

[2]

Click the [Adjustment] tab under the [Utility] tab.

[3]

Click [PF Print].

• The remote panel of VSM launches.

Note

VSM can be launched directly.

"Launching VSM" on page 9

Summary of Contents for VJ-628 ValueJet

















































































Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands

MUTOH VJ-628 ValueJet, Operation Manual

Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands