background image

 

12 

LLS: 

Low loss voltage in ECO mode in parameter 2. 

For 208/220/230/240 VAC models, the setting range in 
parameter 3 is from -7V to -24V of the nominal voltage.   
For 110/115/120/127 VAC models, the setting voltage in 
parameter 3 is from -3V to -12V of the nominal voltage.   

 

06: Bypass enable/disable when UPS is off 

Interface 

Setting 

 

Parameter 3: 

Enable or disable Bypass function. You may 

choose the following two options:   

ENA:

 Bypass enable 

DIS:

 Bypass disable 

 

07: Bypass voltage range setting 

Interface 

Setting 

 

Parameter 2 & 3: 

Set the acceptable high voltage point 

and acceptable low voltage point for Bypass mode by 
pressing the Down key or Up key. 

HLS: 

Bypass high voltage point 

For 208/220/230/240 VAC models: 

230-264:

 setting the high voltage point in parameter 3 

from 230Vac to 264Vac.   
For 110/115/120/127 VAC models:   

120-132:

 setting the high voltage point in parameter 3 

from 120Vac to 132Vac 

LLS: 

Bypass low voltage point 

For 208/220/230/240 VAC models: 

170-220: 

setting the low voltage point in parameter 3 

from 170Vac to 220Vac 
For 110/115/120/127 VAC models:   

85-115: 

setting the low voltage point in parameter 3 from 

85Vac to 115Vac. 

 

08: Programmable outlets enable/disable 

Interface 

Setting 

 

Parameter 3: 

Enable or disable programmable outlets.   

ENA:

 Programmable outlets enable 

DIS:

 Programmable outlets disable 

 

09: Programmable outlets setting 

Interface 

Setting 

 

Parameter 3: 

Set up backup time limits for programmable 

outlets.   

0-999: 

setting the backup time limits in minutes from 

0-999 for programmable outlets which connect to 
non-critical devices on battery mode. 

 

00: Exit setting 

Summary of Contents for POWERMUST 1008 ONLINE LCD



















Reviews: