manualshive.com logo in svg

Mustang Survival MD3188, Manufacturer'S Manual

The Mustang Survival MD3188 is a high-quality inflatable life vest designed to ensure your safety in water. It comes with a comprehensive Manufacturer's Manual that provides detailed instructions on how to use and maintain the product. To access this manual, simply visit our website and download it for free.

Share
Download
background image

6

SIZING AND FIT

This PFD provides a minimum of 33.7 pounds (150 N) of buoyancy 
when inflated and is designed for wearers over 16 years of age, with 
a chest range of 30-52 inches (76-132 cm) weighing over 80 pounds 
(36 kg).

PUTTING ON (DONNING) YOUR PFD 

It is important that the PFD is properly adjusted to fit the person 
wearing it. An incorrect fit or improper fastening of attachments 
could impede its effectiveness.

1.  All belts and straps are already threaded correctly and only need 

to be adjusted for fit. The belt should fit below your rib cage, 
adjusted to a tight personal fit.

2.  Put the PFD on just like a jacket and fasten the front buckle (Fig. 3).

WARNING: LOOSE VEST OR LOOSE ENDS CAN MAIM OR KILL YOU.

3.  Adjust the waist belt for a snug fit using the side buckle on the 

belt (Fig. 3).

4.  Reposition the plastic sliding loop as far back as possible to keep 

the free end from hanging loose.

5.  Wrap and tuck any remaining loose straps around belt.

6.  Recheck loose ends and readjust as needed.

WARNING: DO NOT WEAR INFLATABLE PFDS UNDER CLOTHING AS THE INFLATION 
COULD BE RESTRICTED OR YOU COULD BE INJURED.

FIGURE 3

 

 

DONNING YOUR PFD

Summary of Contents for MD3188





































Reviews:

No comments

Related manuals for MD3188

Brands by name

Popular brands

Load more brands