manualshive.com logo in svg

Murdock BF38 Series, Installation & Maintenance Instructions Manual, Page: 8 / 16

Share
Download
Murdock BF38 Series Installation & Maintenance Instructions Manual Download Page 8

1. -BAT Battery Operation: Peel off paper backing from hook & loop pads then press battery holder firmly 

in place. (See Ref. Below). Connect the battery holder wires to the red sensor wires. Unit requires six 
AA, alkaline or lithium batteries (not included). Note: When the battery holder is connected, the unit 
active.

1A. Plug-In Operation: Plug transformer provided into GFCI protected electrical service, used by the semi-

recessed bottle filler. Plug in transformer to power supply and connect to red sensor wire.

ELECTRICAL INSTALLATION:

NOTE: PLUG IN POWER IS A STANDARD FEATURE. 

2. Connect the blue sensor wires to the solenoid valve wires.(See Below) 

FOR -BAT BATTERY OPERATION OPTION.

TRANSFORMER WIRING AND WATER TUBING CONNECTIONS:

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

7013-037-001

Revised: 07/26/18

Page 8 of 16

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

Semi-Recessed Bottle Fillers

 

Plug-In

Transformer

18" PE Tubing

Sensor

Solenoid Valve

Inlet Fitting

Solenoid Valve

Outlet Elbow

w/ Flow Control

Optional -BAT 9V Battery Pack

Fill Spout

Electrical
Knockout

Thermostat

Adjustment

Removable

Access Door

Keys

MF10 MOUNTING

FRAME ASSEMBLY

1/4" NCT x 1/4" OD

"Y" Strainer

(Chiller Inlet)

1/4" NCT x 1/4" OD

Push-In Union

(Chiller Outlet)

Air-Control Valve

Inlet Fitting

Summary of Contents for BF38 Series

















Reviews:

No comments