background image

 

Operation Manual MK200 

 

2.2 Operation 

 

WARNING! 

Risk of injury, burns, electrical shock or fire. Do not change the specification of this appliance. 

 
Be careful not to cause damage to the refrigerant circuit. It contains propane (R290), a natural gas with a 
high level of environmental compatibility. This gas is flammable.  
If damage occurs to the refrigerant circuit, make sure that there are no flames and sources of ignition in 
the room. Ventilate the room. Do not put flammable products or items that are wet with flammable 
products near or on the appliance. 
 

2.3 Disposal 

 

WARNING! 

Risk of injury. Disconnect the appliance from the mains supply. Cut off the mains cable and discard it. 

 
The refrigerant circuit of this appliance is ozone-friendly. Contact your municipal authority for 
information on how to discard the appliance correctly.  
Do not cause damage to the part of the cooling unit that is near the heat exchanger. 
 

3. Placement of dehumidifier 

 
MK200 dehumidifiers are easy to move around, all you need to have is a power source for 220/240V, but 
bear in mind the following: 
 
-  

The dehumidifier should not be placed near radiators or other heat sources or exposed to direct 
sunlight, as it will reduce performance. 

-  

It is beneficial to use a radiator or heating fan to keep the temperature above +2˚C. 

-  

The dehumidifier should stand at least 25cm from a wall or other obstruction, for maximum air flow. 

-  

Ideal is to put it in the center of the room / area. 

 

3.1 Operation of dehumidifier 

If the dehumidifier is transported horizontally, oil may have run out of the compressor and into the closed 
piping system. In such a case, let the dehumidifier stand for a few hours before being used. It is very 
important that the oil runs back into the compressor, otherwise the dehumidifier may be seriously 
damaged.   
 
1.

 

Check that the water reservoir is correctly placed and the float moves freely in the reservoir. 

2.

 

Connect the dehumidifier to a grounded power source.  

3.

 

Select fan speed.   

4.

 

Set the desired humidity level by means of the humidity control. See the section on the humidity 
control. 

 

 

Summary of Contents for MK200















Reviews: