manualshive.com logo in svg

Munix MI CN-90, Instruction Manual, Page: 3 / 8

Share
Download
Munix MI CN-90 Instruction Manual Download Page 3

- 3 - 

 

 

EXPLODED VIEW DRAWING 

 

                                                         

7. NEVER USE OXYGEN, CARBON 
DIOXIDE,

 combustible gases or any other   

bottled gas as a power source for this tool. 

8. DO NOT CONNECT TOOL

 to pressure 

that potentially exceeds 120 PSI (8.3 BAR). 

9. ONLY USE AIR HOSE THAT IS 
RATED 

for 150% of the maximum system 

pressure. Please try to usea 3/8” ID hose con 
nect in nailer with compressor. 

10.DON'T OPERATE TO NEAR ANY 
COMBUSTIBLE

, or any other explosive 

material. Don't operate the tool where it is 
easy producing corrosion, rust or in a having 
heavy powder environment. 

11 DISONNECT TOOL FROM AIR 
SUPLY HOSE

 before doing tool 

maintenance , clearing a jammed fastener, 
leaving work area, moving tool to another 
location, or handing the tool to another 
person.. 

12. ONLY DISCONNECT THE QUICK 
CONNECTOR 

with the connector of the 

body tail portion air inlet, no compressed 
air can be guaranteed when disconnecting. If 
operation is not correct, the tool can Remain 
charged with air after being disconnected and 
still be able to drive a fastener, causing 
personal injury. 

13. REPLACE PARTS AND ACCESSO- 
RIES

. Only allow use same replacement parts 

while servicing. Approved accessories and replacement parts are available. 
 

 

 

 

Summary of Contents for MI CN-90









Reviews:

No comments