mundoclima CL23190 Installation Manual Download Page 2

To install properly, please read this manual at first.

The air conditioner must be installed by qualified persons.

When installing the indoor unit or its tubing, please follow this 
manual as strictly as possible.

When all the installation work is finished, please turn on the power 
only after a thorough check.

No further announcement if there is any change of this manual 
caused by product improvement.

Indoor Unit

Enough room for installation and maintenance.

The ceiling is horizontal and it can afford the weight of the indoor 
unit.

The air inlet and outlet are not impeded and does not affected by 
outdoor air too much.

The air flow can reach every part of the room.

The connecting pipe and drainpipe can be easily extracted out.

1.   INSTALLATION PRECAUTION

2.   INSTALLATION PLACE

NOTE

The installor should illustrate to users how to correctly use 
and maintain the air-conditioner, as well as remind users to 
carefully read and keep both Installation Manual and Owner's 
Manual well.   

There is no direct radiation from heat source.

Outdoor Unit

Enough room for installation and maintenance.

The air inlet and outlet are not impeded and does not affected by 
outdoor air too much.

Dry and well ventilated place.

The supporter is flat and horizontal and can afford the weigh of 
outdoor unit, without noise and vibration.

The noise and the outlet air will not influence your neighbor.

No combustible gas.

Place convenient for piping and wiring.

Please keep away from the following places, or malfunction may 
be caused.(if unavoidable, please consult the professionals):

There is mineral oil like the oil of cutting machine.

There is much salty air. (Near the coast)

There is caustic gas such as sulfuric gas. (Near the hotspring.)

Factory where the voltage fluctuate greatly.

In the car or in the cabin.

In the kitchen or a place full of oil steam.

There is strong electromagnetic wave.

CONTENTS

PAGE

INSTALLATION PRECAUTION..................................................................1
INSTALLATION PLACE............................................................................1
ACCESSORIES....................................................................................2
INDOOR UNIT INSTALLATION ..............................................................2
INSTALLATION SPACE..........................................................................10
HIGH STATIC PRESSURE TYPE...........................................................11
DUCT DESIGN.....................................................................................12
THROTTING COMPONENTS MAAINTENANCE......................................12
CONNECTION  CONDITION..................................................................12
REFRIGERANT PIPE............................................................................13
INSTALL THE CONNECTING PIPE........................................................13
REFRIGERANT PIPE CONNECTION......................................................14
CONNECT THE DRAIN PIPE.................................................................15
WIRING...............................................................................................15
CONTROL............................................................................................16
TROUBLE SHOOTING..........................................................................18
INSTALL ELECTRIC THROTTLE PART..................................................18
INSTALL BRANCH PIPE.......................................................................19
TEST OPERATION................................................................................19

DISPOSAL

˖

Do not dispose this product as unsorted municipal 

waste. Collection of such waste separately for special treatment 
is necessary.

This appliance is not intended for use by persons (including children) 
with reduced physical, sensory or mental capabilities, or lack of 
esperience and knowledge ,unless they have been given supervision 
or instruction concerning use of the appliance by a person responsible 
for their safety.
Children should be supervised to ensure that they do not play with 
the appliance.

Disconnect the power supply before cleaning and maintenance.

The appliance must be installed 2,3m above floor.

The appliance shall not be installed in the laundry.

If the supply cord is damaged, it must be replaced by the 
manufacturer or its service agent or a similarly qualified person 
in order to avoid a hazard.

 An all-pole disconnection switch having a contact separation of 
at least 3mm in all poles should be connected in fixed wiring.

The appliance shall be installed in accordance with national 
wiring regulations.

The temperature of refrigerant circuit will be high, please keep 
the interconnection cable away from the copper tube.

An all-pole disconnection device which has at least 3mm 
separation distance in all pole and a residual current 
device(RCD)with the rating of above 10mA shall be incorporated 
in the fixed wiring according to the national rule.

The power cord type designation is H05RN-R/H07RN-F or above.

CAUTION

0 1 2

F

3

E

4

D

5

C

6

B

7

A

89

Installation manual

Duct 100% fresh air

1

Summary of Contents for CL23190























Reviews: