Multitech ISI9234PCIE At Commands Reference Manual Download Page 45

Page: 45 / 66

Chapter 4 – Voice Commands

Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434H)

Voice +V Commands Detail

+FCLASS=8

Select Voice Mode

Description:

The +FCLASS=8 command selects voice mode.

+VNH

Automatic Hang-Up Control

Description:

Enables or disables automatic hang-up.

Syntax: AT+VNH=<hook>
Values: <hook>

+VNH=0

Enables automatic hang-ups as in non-Voice modes (such as
hanging up the phone when the modem does not detect a data
carrier within a given time interval).

+VNH=1

Disables automatic hang-ups in non-Voice modes.

+VNH=2

Disables automatic hang-ups in non-Voice modes. The modem
performs only a "logical" hang up (i.e., returns the OK result code).

Reports:

+VNH?

Displays current or selected values.

+VNH=?

Displays list of supported values.

Result Codes:

OK if command accepted.

ERROR if parameter is out of range.

+VIP

Initialize Voice Parameters

Description:

The +VIP command causes the modem to initialize all Voice parameters to the
factory default settings.

Syntax: AT+VIP
Values: None

+VRX

Enter Voice Receive State

Description:

Start voice reception.

Syntax: AT+VRX
Values: None
Result Codes:

ERROR if not in voice mode.

Downloaded from

Elcodis.com

electronic components distributor

Summary of Contents for ISI9234PCIE



































































Search results

Summary of Contents for ISI9234PCIE

Reviews:

Related manuals for ISI9234PCIE

Brands by name

Popular brands

Multitech ISI9234PCIE, At Commands Reference Manual

Search results

Summary of Contents for ISI9234PCIE

Reviews:

Related manuals for ISI9234PCIE

Brands by name

Popular brands