Multitech ISI9234PCIE At Commands Reference Manual Download Page 13 | Manualshive

Page: 13 / 66

background image

Chapter 1 – AT Commands, S-Registers, and Result Codes

Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434H)

13

X

Select Result Code and Monitor Call Progress

Description:

Use this command to enable tone detection options used in the dialing process. As
each function is chosen, the modem’s result codes are also affected. Therefore, this
command is frequently used to control the modem’s responses. The primary function
of this command is to control call response capabilities.

Function Enabled

Disabled

Ext Result Codes

Modem displays basic result
codes, connect messages with
data rate, and an indication of
the modems error correction
and data compression
operations.

Modem displays the basic
result codes.

Dial Tone Detect

Modem dials upon detection of
a dial tone, and disconnects the
call if the dial tone is not
detected within 10 seconds.

Modem dials a call regardless
of whether it detects a dial
tone. Register S6 contains
the dial delay.

Busy Tone Detect

Modem monitors for busy tones.

Modem ignores any busy
tones it receives.

Syntax: ATX<value>

Values:

Command

Extended Result Codes Dial Tone Detect

Busy Tone Detect

0

Disabled Disabled

Disabled

1

Enabled

Disabled

Disabled

2

Enabled

Enabled

Disabled

3

Enabled

Disabled

Enabled

4

Enabled

Enabled

Enabled

5,

6

Enabled

Enabled

Enabled

7

Disabled

Enabled

Enabled

Default: 4
Result Codes:

OK

if <value> = 0 to 7.

ERROR

if <value>

≠

0 to 7.

Call Progress Result Codes:

Command Result

Codes

0

OK, RING, ERROR, CONNECT, NO CARRIER

1

OK, RING, ERROR, CONNECT<RATE>, NO CARRIER

2

OK, RING, ERROR, CONNECT<RATE>, NO CARRIER, NO DIALTONE

3

OK, RING, ERROR, CONNECT<RATE>, NO CARRIER, BUSY,
BLACKLISTED

4

OK, RING, ERROR, CONNECT<RATE>, NO CARRIER, BUSY,
BLACKLISTED, DELAYED, NO DIALTONE, CALL WAITING
DETECTED

5, 6

OK, RING, ERROR, CONNECT<RATE>, NO CARRIER, BUSY,
BLACKLISTED, DELAYED, NO DIALTONE, CALL WAITING
DETECTED

7

OK, RING, ERROR, CONNECT, NO CARRIER

Z

Reset and Recall Stored Profile

Description:

Use this command to make the modem go on-hook and restore the profile saved by
the last

&W

command.

Note:

Both

Z0

or

Z1

restore the same profile (See &W – Store Current Configuration).

Agere Systems controller-based modems have only one stored profile.

Syntax: ATZ<value>
Values:

0

Reset and restore stored profile (saved by the last

&W

command).

1

Same

as

Z0

.

Default: None

Result Codes: OK

if <value> = 0 to 1.

ERROR if <value>

≠

0 to 1.

Downloaded from

electronic components distributor

«
...
11
12
13
14
15
...
»

Summary of Contents for ISI9234PCIE



































































Reviews:

No comments

Related manuals for ISI9234PCIE

Brand: GE Pages: 146

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 103

NI PXI-1042 Series

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 17

Brand: XESS Pages: 23

Brand: OpenVox Pages: 13

Brand: Dantel Pages: 62

Brand: A4Tech Pages: 8

Brand: ebm-papst Pages: 13

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Altera Pages: 33

Brand: Homeworks Pages: 24

Brand: LevelOne Pages: 2

Brand: ELSA Pages: 60

Brand: Helmholz Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands