background image

page 8 — HTXD6i/STXD6i Trowel • SeTUp, aDJUSTMeNTS aND CalIBraTIoNS — rev. #0 (03/14/13) 

TraNSporTINg SaFeTY

  CaUTIoN

 

„

Never

 allow any person or animal to 

stand underneath the equipment while 

lifting.

 

„

Ride-on  trowels  are  very  heavy  and 

awkward to move around. Use proper 

heavy lifting procedures and 

Do NoT

 

attempt to lift the trowel by the guard rings.

  NOTICE

 

„

The easiest way to lift the trowel is to utilize the lift loops 

that are welded to the frame. These lift loops are located 

to the left and right sides of the operator’s seat.

  A  strap  or  chain  can  be  attached  to  these  lift  loops, 

allowing a forklift or crane to lift the trowel up onto and 

off of a slab of concrete. The strap or chain should have 

a minimum of 2,000 pounds (1,000 kg) lifting capacity 

and the lifting gear must be capable of lifting at least this 

amount.

 

„

Never

 transport trowel with fl oat pans attached unless 

safety catches are used and are specifi cally cleared for 

such transport by the manufacturer.

 

„

Never

  hoist  the  trowel  more  than  three  feet  off  the 

ground with fl oat pans attached.

 

„

Before  lifting,  make  sure  that  the  lift  loops  are  not 

damaged.

 

„

Always  make  sure  crane  or  lifting  device  has  been 

properly secured to the lift loops of the equipment.

 

„

alwaYS

 shutdown engine before transporting.

 

„

Never

 lift the equipment while the engine is running.

 

„

Tighten fuel tank cap securely and close fuel cock to 

prevent fuel from spilling.

 

„

Use adequate lifting cable (wire or rope) of suffi cient 

strength.

 

„

Do NoT

 lift machine to unnecessary heights.

 

„

alwaYS

  tie  down  equipment  during  transport  by 

securing the equipment with rope.

TowINg SaFeTY

  CaUTIoN

 

„

Check with your local county or state safety 

towing regulations, in addition to meeting 

Department  of Transportation  (DOT) 

Safety Towing Regulations, 

before towing 

your trowel.

 

„

In order to reduce the possibility of an accident while 

transporting the trowel on public roads, 

alwaYS

 make 

sure the trailer that supports the trowel and the towing 

vehicle are mechanically sound and in good operating 

condition.

 

„

 

alwaYS 

shutdown engine before transporting

 

„

Make sure the hitch and coupling of the towing vehicle 

are  rated  equal  to,  or  greater  than  the  trailer “gross 

vehicle weight rating.”

 

„

alwaYS 

inspect the hitch and coupling for wear. 

Never

 

tow a trailer with defective hitches, couplings, chains, etc.

 

„

Check the tire air pressure on both towing vehicle and 

trailer. 

Trailer tires should be infl ated to 50 psi cold

.

 

Also check the tire tread wear on both vehicles.

 

„

alwaYS 

make sure the trailer is equipped with a 

safety

 

chain.

 

„

alwaYS

 properly

 

attach trailer’s safety chains to towing 

vehicle.

 

„

alwaYS

 make sure the vehicle and trailer directional, 

backup,  brake  and  trailer  lights  are  connected  and 

working properly.

 

„

DOT Requirements include the following:

  • Connect and test electric brake operation.
  • Secure portable power cables in cable tray with tie 

wraps.

 

„

The maximum speed for highway towing is 55 MPH unless 

posted otherwise. Recommended off-road towing is not to 

exceed 15 MPH or less depending on type of terrain.

 

„

Avoid sudden stops and starts. This can cause skidding, 

or  jack-knifi ng.  Smooth,  gradual  starts  and  stops  will 

improve towing.

 

„

Avoid sharp turns to prevent rolling.

safety information

Summary of Contents for Whiteman HTXD6i

































Reviews: