background image

PAGE 4 — TB12SE/TB12PE TUFFTRUK POWER BUGGY • OPERATION MANUAL — REV. #0 (04/01/22)

SAFETY INFORMATION

 

„

NEVER

 use accessories or attachments that are not 

recommended by Multiquip for this equipment. Damage 

to the equipment and/or injury to user may result.

 

„

ALWAYS

 know the location of the nearest 

fi re extinguisher.

 

„

ALWAYS 

know the location of the nearest 

fi rst aid kit.

 

„

ALWAYS

 know the location of the nearest phone or 

keep 

a phone on the job site.

 Also, know the phone numbers 

of the nearest 

ambulance, doctor 

and 

fi re department. 

This information will be invaluable in the case of an 

emergency.

TUFFTRUK SAFETY

  DANGER

 

„

NEVER

 operate the equipment in an explosive 

atmosphere or near combustible materials. An 

explosion or fi re could result causing severe 

bodily harm or even death.

  WARNING

 

„

Accidental starting can cause severe injury or death.

 

ALWAYS

 place the ON/OFF switch in the OFF position.

 

„

NEVER

 disconnect any 

emergency or safety devices.

 

These devices are intended for operator safety. 

Disconnection of these devices can cause severe injury, 

bodily harm or even death. Disconnection of any of these 

devices will void all warranties.

 

„

NEVER

 approach power lines with any part of the 

TuffTruk unless all local, state/provincial and federal 

(OSHA) required safety precautions have been taken. 

Use extreme caution when approaching high voltage 

power lines.

  CAUTION

 

„

ALWAYS 

inspect the surface over which you will travel.  

Look for holes, drop-offs and obstacles.  Look for rough 

and weak spots on docks, ramps or fl oor.

 

„

ALWAYS

 Look for oil spills, wet spots and slippery 

surfaces. Look for soft soil, deep mud and standing water. 

Watch for anything that might make you lose control or 

cause the TuffTruk to tip over.

 

„

ALWAYS 

clear away trash and debris.  Pick up anything 

that might puncture the tires.

 

„

ALWAYS 

make sure aisles, ramps, doorways and 

passages are clear.

 

„

ALWAYS

 plan your work. Make sure you know where 

you will make your pickups, dumps and turns.  Before 

you take a load, know where you will place it.

 

„

NEVER 

travel down a slope with 

full load

. The possibility exists 

of tipping.

 

„

DO NOT 

operate the TuffTruk on 

unsafe haul roads, load areas, 

and dump areas.

 

„

DO NOT

 operate TuffTruk on excessive slopes with a 

grade higher than 25° (45%), forward and backward. 

 

„

DO NOT

 operate TuffTruk on extremely uneven surfaces.

 

„

NEVER

 allow people to ride inside the tub/bucket.

 

„

DO NOT

 operate the TuffTruk at excessive speeds.

Reckless operation may cause accidents and severe 

injury. Slow down when approaching people, wet areas, 

and going up and down grades. It is the responsibility of 

the operator to adjust speed, as necessary, depending 

on the conditions of the road or path.

 

„

Forward travel speed should not exceed 4 mph 

(6.44 km/h). Reverse travel speed should not exceed 

1.5 mph (2.42 km/h).

 

„

ALLOW

 extra time to stop when operating the TuffTruk 

on wet surfaces or loosely graded materials. 

 

„

DO NOT

 dump materials from bucket/tub while the 

TuffTruk is moving.

TIPPING OF BUGGY

 CAN OCCUR

WARNING

Summary of Contents for TuffTruk EB500



































Reviews: