![background image](http://html.mh-extra.com/html/multiquip/sfg10e/sfg10e_operation-and-parts-manual_1855075012.webp)
SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #2 (05/28/09) — PAGE 12
ASSEMBLY INSTRUCTIONS/OPERATIONS
Assembly
The SFG10E SURFACE GRINDER is shipped from the
factory secured on a specially designed wooden pallet
and protected from external damage by a corrugated carton
or wood crate. If shipped with a corrugated carton, the
SURFACE GRINDER can be secured to the pallet by wood
laths nailed to the pallet body. Remove the carton or crate
immediately upon receipt using suitable tools to remove
the nails.
REMOVING THE SURFACE GRINDER FROM THE
PALLET
Tools Required:
1 set of pliers.
1 claw hammer or a hammer and an appropriate pry bar.
The SURFACE GRINDER is secured to the pallet with
steel banding. Using the pliers, cut and remove the
banding. The SURFACE GRINDER can then be removed
from the pallet.
Visually inspect the shipment for freight damage and/or
missing parts. If shipping damage is evident, contact the
delivering carrier immediately to arrange for an inspection
of the damage by their claims representative. Federal law
requires that a claim be filed within a specific time period. If
missing parts are detected, notify your dealer who will assist
you in obtaining them.
The SURFACE GRINDER is shipped from the factory
completely assembled. If ordered with the SURFACE
GRINDER, multi-accessory attachments are normally
shipped separately to minimize the potential for loss during
shipment.
Check all fasteners for proper security. Consult a fastener
torque chart for the proper torque value if any fastener is
found to require retorquing.
After April 1, 1996 all single head SURFACE GRINDERS
are shipped from the factory with the SFSG121000 Safety
and Dust Shield Assembly Kit. The SFSG121000 Safety
and Dust Shield is designed to perform the following job
functions:
1)
To contain loose materials within the platform area of
the SURFACE GRINDER as a direct result of a specific
grinding process. This includes materials removed from
the surface as well as any slurry mixture utilized to
help maximize material removal efficiencies.
2)
To provide a method for a vacuum system to help
remove airborne dust related materials from within the
skirt assembly. Dust related materials are usually
created as a result of the grinding process. A specific
job application may require the reduction and/or
minimization of airborne dust related materials from the
atmosphere while the SURFACE GRINDER is being
operated. The kit includes a hose and necessary
hardware to connect the skirt assembly to the 3 inch
diameter vacuum attachment fitting located at the rear
of the machine. Use of the kit along with a suitable
vacuum system will not completely remove all airborne
and loose materials directly from the work surface.
DANGER
DANGER
DANGER
DANGER
DANGER
WEAR SAFETY GLASSES AND OTHER APPROPRI-
ATE SAFETY APPAREL WHEN CUTTING THE STEEL
BANDING AND/OR REMOVING THE CORRUGATED/
WOOD SHIPPING CRATE.
DANGER
DANGER
DANGER
DANGER
DANGER
USE OF THE SFSG121000 SAFETY AND DUST SHIELD
ASSEMBLY KIT ALONG WITH A SUITABLE VACUUM
SYSTEM WILL NOT COMPLETELY REMOVE ALL
LOOSE MATERIALS FROM THE WORK SURFACE.
HAZARDOUS CLASSIFIED, LOOSE MATERIALS MUST
BE REMOVED FROM THE WORK SURFACE BY PRO-
CESSES AND/OR PROCEDURES MEETING THE
APPLICABLE OSHA AND/OR EPA REQUIREMENTS.
DANGER
DANGER
DANGER
DANGER
DANGER
THE USE OF THE SFSG121000 SAFETY AND DUST
SHIELD ASSEMBLY KIT ALONG WITH A SUITABLE
VACUUM SYSTEM TO REMOVE HAZARDOUS
CLASSIFIED, AIRBORNE MATERIALS FROM THE
WORK SURFACE WILL NOT ELIMINATE THE
REQUIREMENT FOR PROPER SAFETY RELATED
EQUIPMENT, OPERATING PLAN AND/OR
PROCEDURES.