MULTIQUIP MQP20P Page 29 Operation And Parts Manual Download

Page: 29 / 80

MQp20p STaNDBY geNeRaTOR • OpeRaTiON aND paRTS MaNual — Rev. #1 (11/28/11) — page 29

JaCkeT WaTeR HeaTeR aND iNTeRNal BaTTeRY

CHaRgeR

This generator is equipped with a jacket water heater and

an internal battery charger. They are provided with electric

cords to connect to a commercial power source.
These units will

ONlY

function when commercial power has

been supplied to them (Figure 21). When using extension

cords, refer to Table 7 for the correct size and length.
The battery charger should always be connected to a

commercial power source to ensure that the battery does

not get discharged.
When using the generator in

hot

climates there is no

need to apply power to jacket water heater. However, if the

generator will be used in

cold

climates, it is best to apply

power to the jacket water heater at all times.

StartuP

Figure 21. Battery Charger and Jacket Water

Heater Power Connections

Battery

Charger

Connect to external

120 VAC power source

Jacket

Water

Heater

Summary of Contents for MQP20P

















































































Search results

Summary of Contents for MQP20P

Reviews:

Related manuals for MQP20P

Brands by name

Popular brands

MULTIQUIP MQP20P, Operation And Parts Manual

Search results

Summary of Contents for MQP20P

Reviews:

Related manuals for MQP20P

Brands by name

Popular brands