![background image](http://html1.mh-extra.com/html/multiquip/mp1415e/mp1415e_operation-and-parts-manual_1855314029.webp)
MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 29
5. Grasp the starter grip (Figure 28) and slowly pull it out. The
resistance becomes the hardest at a certain position, corre-
sponding to the compression point. Pull the starter grip briskly
and smoothly for starting.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
DO NOT
pull the starter rope all the way to
the end.
DO NOT
release the starter rope
after pulling. Allow it to rewind as soon as
possible.
4. Rotate the
throttle lever
(Figure 27) halfway between
fast
and
slow
for starting. All cutting is done at
full throttle
. The
engine governor speed is factory set to ensure optimum
blade operating speeds.
Figure 27. Throttle Lever
6. If the engine has started, slowly return the choke lever
(Figure 26) to the
"OPEN"
position. If the engine has not
started repeat steps 1 through 5.
7. Before the saw is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guards and/or covers.
8. Gradually move the engine throttle lever toward the
fast
position. (
All cutting should be done at full
throttle
).
OPERATION (GASOLINE)
ALWAYS
cut with the saw at
FULL THROTTLE.
Attempting to
cut with the saw at less than full throttle could cause the blade to
bind or stop abruptly in the slab resulting in serious injury to the
operator or others in the area.
10. Push the
conveyor cart
with the material, slowly and evenly
until the cut is complete. Move the cart back and remove
the cut pieces.
11. Avoid overloading the engine when cutting. In the event that
the engine becomes overloaded, turn the
engine
ON/OFF
switch to the
OFF
position and allow the engine to
cool
before
attempting to restart.
STOPPING
1
.
Set the engine throttle lever to
slow
speed and let the engine
idle for 3-5 minutes.
2.
Turn the engine
ON/OFF
switch to the
"OFF"
position.
3.
Place the fuel valve lever in the
closed
position.
4.
Let the engine cool.
5.
Using a soft cloth, clean any excess debris or residue that
may have accumulated on the saw.
6.
Store saw in a clean dry location where it will be out of the
reach of children.
DO NOT
NEVER
WARNING
ALWAYS
be alert to the fact that there is a rotating blade on the
saw and be extremely aware of your body position - especially
your hands in relationship to the rotating blade. The possibility
exists of
severe bodily harm even death
if your body comes in
contact with the rotating saw blade.
DANGER
9.
Squeeze the water pump
priming bulb
(Figure 29)until
water begins to flow through the
water lines. If the pump is working
correctly, the cutting blade should be
covered with a steady water mist.
This will keep the blade cool.
WARNING
Figure 29. Priming Bulb
Figure 28. Starter Grip
Summary of Contents for MP1415E
