MULTIQUIP EM120 Operation And Parts Manual Download Page 40

Page: 40 / 58

PAGE 40 — EM120 HYD. PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/09/19)

NAMEPLATE AND DECALS ASSY.

P/N 521232

CAUTION

1. Use manufacturer’s recommended torque values
when tightening wheel lug nuts.
2. Use manufacturer’s recommended tire pressure

values when inﬂating tires.

DO NOT

exceed

recommended tire pressure.

INSPECT BEFORE TOWING

TIGHTNESS OF WHEEL NUTS
TIRE PRESSURE

P/N 521232

CAUTION

1. Use manufacturer’s recommended torque values
when tightening wheel lug nuts.
2. Use manufacturer’s recommended tire pressure
values when inﬂating tires.

DO NOT

exceed

recommended tire pressure.

INSPECT BEFORE TOWING

TIGHTNESS OF WHEEL NUTS
TIRE PRESSURE

Keep safety grate, guards and doors

in place. Shut off engine or electric

motor before inspection or maintenance.

Moving parts can cut and crush.

engine or electric motor

before placing hands in mixing drum.

SHUT OFF

This machine to be operated by qualiﬁed

personnel only. Ask for training as needed.

P/N 521229

WARNING

To avoid injury, you

read and

understand operator’s manual before

using this machine.

MUST

Keep safety grate, guards and doors

in place. Shut off engine or electric

motor before inspection or maintenance.

Moving parts can cut and crush.

engine or electric motor

before placing hands in mixing drum.

SHUT OFF

This machine to be operated by qualiﬁed

personnel only. Ask for training as needed.

P/N 521229

WARNING

To avoid injury, you

read and

understand operator’s manual before

using this machine.

MUST

SAFETY

INSTRUCTIONS

1. Read owner’s manual

before operating.

2. Keep unauthorized and untrained

people away from machine during

operation.

3. Make sure all safety devices are in

place before this machine is started.

4. Make sure engine is turned off and

spark plug wire is disconnected before

cleaning the machine.

5. Keep hands and ﬁngers away from

moving objects.

6. Do not operate machine in an enclosed

area, proper ventilation is required.

7. Never leave machine unattended when

operating.

8. Always stop engine and allow engine

to cool before adding fuel or oil.

520935

QUALITY

MANAGEMENT SYSTEM

CERTIFIED ON

ISO 9001:2008

518524

P/N 13238

Summary of Contents for EM120



























































Search results

Summary of Contents for EM120

Reviews:

Related manuals for EM120

Brands by name

Popular brands

MULTIQUIP EM120, Operation And Parts Manual

Search results

Summary of Contents for EM120

Reviews:

Related manuals for EM120

Brands by name

Popular brands