MULTIQUIP EM120 Operation And Parts Manual Download Page 22

Page: 22 / 58

PAGE 22 — EM120 HYD. PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/09/19)

HYDRAULIC OIL

Check hydraulic oil sight gauge (Figure 8) to ensure that

hydraulic oil is at the 3/4 level.

Figure 8. Hydraulic Oil Sight Gauge

HYDRAULIC HOSES

Check

all

hydraulic hoses to make sure they are not worn,

frayed or defective.

PADDLE BLADE CHECK

Check for

worn

defective

paddle blades (Figure 9).

Make sure that all blades are adjusted properly. See blade

adjustment procedure in this manual. Replace all defective

or damaged blades immediately using the part numbers

referenced in the parts section of this manual.

Figure 9. Worn Mixing Blade

WORN RUBBER

MISSING

RUBBER

MISSING

RUBBER

CRACKS

INSPECTION

TIRES

Check for

worn

defective

tires (Figure 10). Replace any

defective or worn tires immediately.

Figure 10. Tire Wear

START/STOP SWITCH

This unit has been equipped with a start/stop switch

(Figure 11), which should be tested every time the unit

is started.

Figure 11. Start/Stop Pushbutton Switch

CUT

MISSING

RUBBER

CRACKS

DEFORMED

BALDNESS

Summary of Contents for EM120



























































Search results

Summary of Contents for EM120

Reviews:

Related manuals for EM120

Brands by name

Popular brands

MULTIQUIP EM120, Operation And Parts Manual

Search results

Summary of Contents for EM120

Reviews:

Related manuals for EM120

Brands by name

Popular brands