
Operating Instructions for RX-5 M-LINK /
RX-7 M-LINK 2.4 GHz receivers
Page 16
Instru
ctions
for
RX
-5
/7 M-L
INK
2.4
G
H
z r
e
cei
v
er
s #
985
5
312 LA
30
.09.2014
•
Err
o
rs
and
omi
s
sions excep
ted
! •
MU
LTI
P
L
E
X
When the Send process is complete, the screen
displays “--> OK!“ (= complete!).
Disconnect the receiver, switch off the
MULTImate
.
2. Activating using the
MULTIPLEX Launcher
:
At
“More
settings
Options“ / “Weitere Einstellungen
Optionen…“ (= More settings
Options) select the
following menu point:
“Digital servodata“ / “Digitale Servodaten“
(= Digital servo data).
Click on the “Accept“ / „Übernehmen“ button
(= Accept).
Click on the „Send data“ / “Daten senden“ button
(= Send data).
Click on the “Close“ / “Beenden“ button
(= Finish).
Close
MULTIPLEX Launcher
, disconnect the receiver.
3. Connect the three-core lead (
# 8 5070
) to the receiver’s B/D
socket.
4. Connect the lead to the power supply / servo management
system, or to the flybarless system (see the operating
instructions supplied with these devices).
!
Take care to connect the lead correctly, i.e. the con-
nectors must be correctly orientated, and - especially
when using non-MULTIPLEX products - the pin assign-
ment must be compatible. Be sure to check the symbols
on the
M-LINK receiver, and on the non-MULTIPLEX
product if present. Refer to the operating instructions of
the non-MULTIPLEX device, and ask the manufacturer if
you are in any doubt!
12.
S
ELECTING ONE
S
ENSOR
A
DDRESS AS
“P
RIORITY
A
DDRESS
”
The telemetry-capable
RX-5/7 M-LINK
receivers permit the user
to define any one of the sensor addresses (0 … 15) as a “priority
address”:
This one selected sensor value is then updated at a higher rate
than all the other sensor values.
Typical application: “Vario”:
The audio output for climb and descent, and the associated on-
screen display, are updated more frequently than the other
sensor values, and are therefore generated without delay.
!
Note:
The “Priority address” option is switched off by default on M-LINK
receivers, and can be activated using the
MULTIPLEX MULTI-
mate
or the
MULTIPLEX Launcher
PC program in conjunction
with the UNI USB PC lead (
# 8 5149
).
This is the procedure for activating the priority address:
1. Activating using the
MULTImate
:
At the menu point “4-6 Sensor addr.“ / “4-6 Sensoradr.“
(= Sensor address) select the option:
“4-6 Prio address“ / “4-6 Prio Adresse“
(= Priority address).
Hold the 3-D digi-adjuster pressed in:
The
MULTImate
displays: “L 0“.
Release the 3-D digi-adjuster.
Press the 3-D digi-adjuster briefly, and select the priority
address (0 … 15).
Press the 3-D digi-adjuster briefly.
Switch to the menu:
“4-6 Go back …to RX M-LINK“ /
“4-6 Zurück …zu RX M-LINK“
(= back … to RX M-LINK)
and confirm by pressing the 3-D digi-adjuster.
Select the menu point:
“4-10 Send data“ / “4-10 Dat. senden“
(= Send data)
and hold the 3-D digi-adjuster pressed in:
The
MULTImate
displays:
“please wait…“ / “bitte warten…“ (= please wait).
Release the 3-D digi-adjuster:
When the Send process is complete, the screen
displays “--> OK!“ (= complete!).
Disconnect the receiver, switch off the
MULTImate
.
2. Activating using the
MULTIPLEX Launcher
:
At “Sensor addresses“ / “Sensorparameter“
(= Sensor address) auswählen:
“Address w/prio 1:“ / “Adresse mit Prio 1:“
(= Address with priority 1).
Select the “Address“ / “Adresse“ (= Address) check-box,
and enter the desired address (0 … 15).
Click on the “Accept“ / “Übernehmen“ button
(= Accept).
Click on the “Send data“ / “Daten senden“ button
(= Send data).
Click on the “Close“ / “Beenden“ button
(= Finish).
Close
the
MULTIPLEX Launcher
, disconnect the
receiver.
This is the procedure for disabling the priority address:
1. Disabling using the
MULTImate
:
At the menu point “4-6 Sensor addr.“ / “4-6 Sensoradr.“
(= Sensor address) select the option:
“4-6 Prio address“ / “4-6 Prio Adresse“
(= Priority address).
!
Note:
The second line of the screen displays the selected
priority address.
Hold the 3-D digi-adjuster pressed in:
The screen entry in the second line changes to:
“L off“ / “L aus“ (= L off).
Switch to the menu:
“4-6 Go back …to RX M-LINK“ /
“4-6 Zurück …zu RX M-LINK“
(= back … to RX M-LINK)
and confirm by pressing the 3-D digi-adjuster.
Select the menu point:
“4-10 Send data“ / “4-10 Dat. senden“
(= Send data)
and hold the 3-D digi-adjuster pressed in:
The
MULTImate
displays:
“please wait…“ / “bitte warten…“ (= please wait).
Release the 3-D digi-adjuster:
When the Send process is complete, the screen
displays “--> OK!“ (= complete!).
Disconnect the receiver, switch off the
MULTImate
.
2. Disabling using the
MULTIPLEX Launcher
:
At “Sensor addresses“ / “Sensorparameter“
(= Sensor parameters) auswählen:
“Address w/prio 1:“ / “Adresse mit Prio 1:“
(= Address with priority 1).
Clear (erase) the tick in the “Address“ / “Adresse“ check-
box (= Address).