User Manual: CoboPin-VT3001C(-I/-T)
V1.00 (10-2013)
12
Available colour presets:
C 0
all off
C10
Frog
C 1
Red
C11
Lavender
C 2
Green
C12
Candy
C 3
Blue
C13
Peach
C 4
Yellow
C14
Aqua
C 5
Pink
C15
Leaf
C 6
Turquoise
C16
Purple
C 7
Lime
C17
Barbie
C 8
Orange
C18
Breeze
C 9
Marine
C19
White
“d3” Mode (DMX 3-Channel RAW Mode)
Press the MODE button (7) until the display shows “d3”, indicating operation in “d3” (3-
channel DMX) mode. Shortly after that, the display shows the DMX starting address.
You can choose any DMX starting address by simply using the UP/DOWN buttons
(5/6). The chosen DMX-address comes effective approximately 3 seconds later and will
show up on the display (2) in alternation to the “d”. This allows control of the unit by any
external DMX signal sending on the chosen channel. In this mode the potentiometer (1)
is disabled.
The unit receives DMX values on a packet of three channels and mirrors the received
data on the DMX output (9). If a DMX signal is present the DMX LED (3) will turn on.
The three channels control the unit as follows:
DMX channel
Value Range
Function
CH1
000-255
Red Intensity
CH2 000-255 Green
Intensity
CH3 000-255 Blue
Intensity
This setting is stored even if the device is switched off.
Note: For master/slave operation, the slave units shall be set to “d3” mode.
“d4” Mode (DMX 4-Channel Combined Master/Strobe Mode)
Press the MODE button (7) until the display shows “d4”, indicating operation in “d4” (4-
Channel DMX) mode. Shortly after that, the display shows the DMX starting address.
You can choose any DMX starting address by simply using the UP/DOWN buttons
(5/6). The chosen DMX-address comes effective approximately 3 seconds later and will
show up on the display (2) in alternation to the “d”. This allows control of the unit by any
external DMX signal sending on the chosen channel. In this mode the potentiometer (1)
is disabled.
User Manual: CoboPin-VT3001C(-I/-T)
V1.00 (10-2013)
5
4. The surface of the device may get hot during operation, and heat
sink areas may reach to or exceed the limits of EN60950. Do not
touch heat sink areas of the device during operation, and allow 20
minutes of cool-down time after powering off before touching.
5. If fluids have spilled into the unit or small parts have intruded the
unit, immediately switch off the unit and hand it over to the
authorized service for a security check.
6. Disconnect the unit from AC supply by pulling the AC plug out of
the wall outlet or the unit’s AC socket during a thunder-storm in
order to avoid any damage on the unit due to AC voltage peaks.
7. In cause of not correct function of this unit or damaged AC cord or
other damaged parts, pull immediately the AC plug out of the wall
outlet and hand the unit over to the authorized service for a
security check.
8. To meet all aspects of functionality and security during mainte-
nance work to be preformed on this unit, all parts should be
replaced by genuine spare parts. Consequently, take care of your
dealer or maintenance company to be authorized by the
manufacturer.
■
Health advice
This unit produces and absorbs electromagnetic radiation. The strength of radiation and
the sensitivity for disturbing interference matches the CE and FCC requirements. A
corresponding sign is printed on the backside of the unit. Any change or modification
may affect the behavior of the unit concerning electromagnetic radiation, with the CE
requirements eventually not to be met any more. The manufacturer takes no
responsibility in this case.
■
Functional advice
This unit is immune to the presence of electromagnetic disturbances – both conducted
and radiated - up to a certain level. Under peak conditions, the unit is classified to show
a “class C” performance criteria and may encounter temporary degradation or loss of
function which may need manual help to recover. In such case, disconnect the AC
power from the unit and reconnect it again to recover.
■
Environmental advice
This unit is built to conform to the ROHS standards and the WEEE
directive 2002/96/EC of the European Parliament and of the Council of
the European Union. Under these regulations, the product shall not be
discarded into regular garbage at the end of its life, but shall be returned
to authorized recycling stations.