Multi-Tech RouteFinder RF550VPN User Manual Download Page 8

Page: 8 / 76

Chapter 1 – Introduction and Description

Multi-Tech Systems, Inc. RF550VPN User Guide

RF550VPN Front Panel

Link

ACT

100

FDX

COL

Data DCD

Serial

WAN

Link RXD TXD

PWR

1 2 3

RF550VPN Light Panel

LEDs

Description

Link ACT

Lights when the LAN client is correctly connected to the Ethernet port. Blinks
when there is activity on the Ethernet port.

100/10

Lights when the LAN client is connected at 100MB.
Off when the LAN client is connected at 10MB.

FDX COL

Lights when the LAN client is connected as full duplex.
Off when the LAN client is connected as half duplex. Blinks when there are
collisions on the network.

Serial Data

Blinks when the Serial async port is receiving or transmitting data.

Serial DCD

Lights when the Serial async port is properly connected to a remote site.

WAN Link

Lights when a successful connection to the 10BaseT WAN is established.

WAN RXD

Lights when the WAN port is receiving data.

WAN TXD

Lights when the WAN port is transmitting data.

PWR

Lights when power is being supplied to the router.

Summary of Contents for RouteFinder RF550VPN













































































Search results

Summary of Contents for RouteFinder RF550VPN

Reviews:

Related manuals for RouteFinder RF550VPN

Brands by name

Popular brands

Multi-Tech RouteFinder RF550VPN, User Manual

Search results

Summary of Contents for RouteFinder RF550VPN

Reviews:

Related manuals for RouteFinder RF550VPN

Brands by name

Popular brands