Multi-Tech RouteFinder RF550VPN User Manual Download Page 18

Page: 18 / 76

Chapter 3 – Configuring the PC

Multi-Tech Systems, Inc. RF550VPN User Guide

The

Local Area Connection Properties

dialog box displays.

Select

Internet Protocol [TCP/IP]

. Once the protocol is selected, the name of your adapter

card should display in the

Connect using

box.

Click the

Properties

button.

The

Internet Protocol (TCP/IP) Properties

dialog box displays. You will set your workstation’s IP

Address.

To set a Dynamic IP Address, check Obtain an IP Address Automatically. Dynamic
Addresses are used in Example 2 – Site B and Example 3 – Site B.

To set a Fixed IP Address, check Specify an IP address. Fixed Addresses are used in all
the examples, except the two mentioned above. For our example, set the address to
192.168.2.x.

Click

Close out of the

Control Panel

Repeat these steps for each PC on your network.

Summary of Contents for RouteFinder RF550VPN













































































Search results

Summary of Contents for RouteFinder RF550VPN

Reviews:

Related manuals for RouteFinder RF550VPN

Brands by name

Popular brands

Multi-Tech RouteFinder RF550VPN, User Manual

Search results

Summary of Contents for RouteFinder RF550VPN

Reviews:

Related manuals for RouteFinder RF550VPN

Brands by name

Popular brands