Muchmore cell master double accel MM-CTXDAB, User Manual

Page: 6 / 32

Discharging LiPo, LiFe
◈ Information of STEP 3 LCD
Discharging current
Battery cell number
Cell voltage
Select LiPo or LiFe and
press Enter button
-select menu 1-
LiPo
◈ STEP 01 ◈
Set Discharge and press button
Charge
1
Discharge
*LiPo*
◈ STEP 02 ◈
※
After all discharge setup, press the button at least 2 seconds, it moves to Check Battery with informing battery check on a screen.
●
Display after the end of the charge
LiPo
CHG 8.40V
12:02
0.0A
2800mA
Setup battery type Finish battery voltage
Finish charging capacity charging time
* You can see each information’s on your screen push the button.
1. Each cell capacity
2. Total resistance value of Batteries
3. Each cell resistance.
(Press the button, detect the resistance and show on the screen,
it need to 5~ 7 seconds to detect)
●
Quit charging, Cancel charging
Press the button for 2 seconds during the charging, stops charging, and the status of CHG (channel), End (channel) messages are
shown on the intersection. At this point, press the button to proceed the Setup screen.
●
Change the value in the charging
On-touch the button, blink the charging current.
At this time press the button, change the value, and press , it change the charging value without stop charge.
Connect the battery
And If you want to cell balance discharge,
connect the Cell balancer too.
1.0A 2S(7.4V)
Cut V
3.2V/Cell
◈ STEP 03 ◈
Discharging
current
Battery
cell number
Cell voltage
●
Check battery cell condition
EQU
USER 2S(7.4V)
2S(7.4V)
USER
Cell number and Voltage from actual user.
If detecting voltage and actual voltage are same, press button, and start to charge
But, if the actual cell number is different from detected cell number, please adjust the
cell number in manual.
EQU
USER
※
Mismatch cell number will cause battery or device damage, please use carefully.
EQU
Auto detect Cell number and Voltage (from Cell Master Double Accel IC).
●
Display discharging
LiPo
DCH
8.35V
8:11
2.0A
122mA
Battery type/
Cell num, Channel
Discharging currents Battery voltage
Mode state Discharging capacity Discharging time
*Optional discharging function key
During the discharge, press button shown 3 information on the
screen. If not press the button, it moves back to discharging mode screen
after 5 seconds.
1. Current capacity of each cell
2. Setting value capacity, Discharging cut Volt value
3. EQU Temp(device temperature), BAT Temp(battery temperature)
●
Cancel Discharging
Press the button for 2 seconds during the discharging, stops discharging, and the status of CHG (channel), End (channel) messages are
shown on the intersection. At this point, press the button to proceed the Setup screen.
LiPo
DCH 8.00V
12:02
0.0A
2800mA
Setup battery type Finish battery voltage
Finish discharging capacity discharging time
: Set the discharging current, enter the value of the amp.
: Select the number of charge the battery pack, specify the number of cells.
If you change the number of cells in the pack voltage will be displayed automatically.
: Set a finish discharge current of each cell.
●
Display after the end of the discharge
* You can see each information’s on your screen push the button.
1. Each cell capacity
2. Total resistance value of Batteries
3. Each cell resistance.
(Press the button, detect the resistance and show on the screen,
it need to 5~ 7 seconds to detect)
5 Muchmore Racing Co., Ltd. SUPER COMPACT DUAL PORT CHARGER/DISCHARGER