manualshive.com logo in svg

MTD OEM-190-180, Operator'S Manual

Share
Download
MTD OEM-190-180 Operator'S Manual Download Page 3

3

SECTION 1:  LOOSE PARTS 

The grass catcher kit is shipped with following loose parts in the carton. Please remove all loose parts, including the 
hardware pack, from the carton before discarding it. Compare with Figure 1 to check that all parts were included. 
Note that the kit and the hardware pack contain extra items which are not used on your unit.

Figure 1

 Contents of Hardware Pack

Figure 2

NOTE: 

Each item has been identified in Figure 2 for ease of assembly, and the letter code assigned here is

maintained in assembly instructions. However, the hardware pack contains more than one of some items.

Chute Tube

Discharge Chute

Assembly

Bag Assemblies

Grass catcher Cover 

Mounting 

Support Tube

(attached to cover)

Assembly

Bracket 

A

B

C

E

F

F1

F2

G

H

For all Model Series 800 tractors only 

For older Model Series 600 tractors only

For decks with grass catcher
pin not pre-installed

For all Model Series 660 through 690 tractors

(Available in Bagger Kit 190-182 only)

A

B

F1

For all Model Series 700 tractors

D

C

Summary of Contents for OEM-190-180













Reviews:

No comments

Brands by name

Popular brands

Load more brands