mspa D-AL04 Alpine After-Sales Service Manual Download

Page: 35 / 37

2019-2020

Delight Service Manual

Visit our website at: www.the-mspa.com

- 35 -

52:

Question:

Where should I install the filter cartridge? Why is there hole(s) on the surface of filter cartridge?

Does the filter cartridge have a filter bag?

Answer

Please screw the filter onto the water inlet (upper fitting with two bulges) on the spa wall by turning it

clockwise, through which water is drawn from the pool by a pump. The hole(s) on the surface of filter

cartridge is a security to make sure there is always minimum water flow to avoid damage to heater and

pump when filter cartridge would be blocked. MSpa does have no cover or bag for the filter cartridge

anymore

53:

Question:

Can I use MSpa in the rain?

Answer

MSpa can leave outside in light rain as it is of IPX5, protection against harmful ingress of water. But we

do not suggest people use it with bubbling open because the water may cause air pump damped and

rusted which could result the air pump works improperly and will void your warranty. And also you’ll need

to make sure to keep the power plug dry.

54:

Question:

What if I already screw off the inlet and outlet when the product was full with water??? Did I

hurt the engine?

Answer

No, it’ll not hurt the engine, but the water leakage is a big problem, which would damage or cause

electric shock if there is any other electrical equipment around the spa

55:

Question

Why there is red light keeps flashing or red and green lights alternately flashing?

Answer This is filter Cartridge Cleaning Reminder: When red light keeps flashing (Filter function is OFF) or

red and green lights alternately flashing (Filter function is ON), the filter cartridge shall be

cleaned or replaced. After that, press Filter button for 3s to delete the reminder.

Chapter 7. Attachment

DELIGHT

Spa Check Flow –E0-E1.pdf (Same as SS18)

DELIGHT

Spa Check Flow –heating failure.pdf (Same as SS18)

DELIGHT

Spa Check Flow -NO DISPLAY.pdf (Same as SS18)

SS20 spare parts list

EU/SW/UK version

Repairing video download link:

https://www.adrive.com/public/Se7C6Z/2019%20delight%20concept

2019-2020 Premium/Elite/Concept trouble shooting easy checking

Problem

Cause

Solution

Water temperature is lower

than

degree

or higher

than 55

degree

Video guide:

Change the water

Summary of Contents for D-AL04 Alpine






































Search results

Summary of Contents for D-AL04 Alpine

Reviews:

Related manuals for D-AL04 Alpine

Brands by name

Popular brands

mspa D-AL04 Alpine, After-Sales Service Manual

Search results

Summary of Contents for D-AL04 Alpine

Reviews:

Related manuals for D-AL04 Alpine

Brands by name

Popular brands