background image

81

RAID Configuration

RAID Configuration

Below are the different types of a RAID.

RAID 0

  breaks the data into blocks which are written to separate hard drives. 

Spreading the hard drive I/O load across independent channels greatly 

improves I/O performance.

RAID 1

  provides data redundancy by mirroring data between the hard drives and 

provides enhanced read performance. 

RAID 5

  provides data striping at the byte level and also stripe error correction 

information. This results in excellent performance and good fault tolerance. 

RAID 10

  uses four hard drives to create a combination of RAID 0 and 1 by forming a 

RAID 0 array from two RAID 1 arrays. 

RAID level comparison

RAID 0

RAID 1

RAID 5

RAID 10

Minimum # drives

2

2

3

4

Data protection

None

Excellent

Excellent

Excellent

Read performance

Excellent

OK

Good

OK

Write performance Excellent

Good

OK

Good

Capacity utilization 100%

50%

67%~(1-1/n)

50%

Using Intel

®

 Rapid Storage Technology Option ROM

First, you need to set the

 SATA mode

 to 

RAID

 in BIOS to create, delete and reset RAID 

volumes. To enter the IRST Option ROM, reboot and press 

Ctrl + I

 keys to enter the 

IRST Option ROM during the POST, the following window will appear.

MAIN MENU

[                     ]

DISK / VOLUME INFORMATION

[                                                ]

4.       Recovery Volume  Options
5.       Acceleration Options
6.       Exit

RAID  Volumes :

None  defined.

Physical  Devices :
Port  Device  Model                 Serial  #                                                  Size    Type/Status (Vol  ID)

1       XXXX-XXXXXXXX          XXXXXXXXXXXXXX                    XXX.XGB

    

Non-RAID  Disk

2       XXXX-XXXXXXXX          XXXXXXXXXXXXXX                    XXX.XGB

    

Non-RAID  Disk

[ ↑↓] - Select                            [ESC] - Exit 

             [ENTER] - Select Menu

1.       Create  RAID  Volume

2.       Delete  RAID  Volume
3.       Reset Disks to Non-RAID

[                        ]

MAIN  MENU

 Important

The following procedure is only available with a newly-built system or if you are 

reinstalling your OS. It should not be used to migrate an existing system to RAID. 

Summary of Contents for Z270 Gaming Pro Carbon Motherboard





























































































Reviews: