background image

Page 8

     MSI-9008 CellScale Multiplexer   

   User Guide

M  E  A  S  U  R  E  M  E  N  T    S  Y  S  T  E  M  S    I  N  T  E  R  N  A  T  I  O  N  A  L

Multiplexer Cable #502305

To connect a secondary Multiplexer to a primary Multiplexer requires the secondary cable assembly, MSI part number
502305. This cable connects from TB2 on the secondary Multiplexer to TB2 on the primary Multiplexer. The following

table shows the connections.

Secondary Multiplexer Cable 502305 Connections

Secondary

Secondary

Primary

Primary

Mux

Mux

Wire

Mux

Mux

TB2 Pin #

Label

Color

TB2 Pin #

Label

1

DIG2

Gray

1

DIG2

2

DIG1

White/Orange

2

DIG1

3

DIG0

White/Gray

3

DIG0

4

GND

Orange

4

GND

7

- SIG Act

White/Black

5

- SIG Pass

8

+ SIG Act

Green/White

6+ SIG Pass

9

- EXC

Black

9

- EXC

10

- Sense

Brown

10

- Sense

11

+ Sense

Blue

11

+ Sense

12

+ EXC

Red

12

+ EXC

Connecting One Multiplexer to CellScale

When connecting a single Multiplexer to a CellScale, the CellScale can control a maximum of nine load cells. This is
accomplished by connecting a Multiplexer with up to eight load cells to one CellScale input and a single load cell to the
second input. The following diagram illustrates this.

This connection requires the use of the pass thru signal to be used for the ninth load cell. This ninth load cell will be
added to the CellScale scan list as channel 2-1. For information about how to setup the CellScale scan list for this
configuration, see the ”Software Setup section.

Summary of Contents for MSI9008















Reviews: