MSD 6520 Installation Instruction Download Page 14

Page: 14 / 24

INSTALLATION INSTRUCTIONS

AUTOTRONIC CONTROLS CORPORATION

• 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

GM IGNITIONS Wiring a Dual Connector Coil.

ORANGE

BOTH

PINKS

BOTH

PINKS

BOTH

WHITES

BOTH WHITES

WHITE

RED

INDICATES CONNECTION

RED

BLACK

MAGNETIC PICKUP

(NOT USED)

HEAVY RED

HEAVY BLACK

TO BATTERY

IGNITION

DIGITAL-6

PN 6520

PROGRAMMABLE

2 STAGE REV-LIMITER

STEP RETARD

CAPACITIVE DISCHARGE

IGNITION

Plus

NOTE: Cut and splice the two pink wires (coil

positive) together and connect to orange

wire of MSD. Cut and splice the two white

wires (coil negative) together and

connect to the white of MSD. If the vehicle

is not equipped with a factory tach, there

will only be one white wire.

BLACK

RED

WHITE

ORANGE

COIL

WIRE

(PINK)

WIRE

(PINK)

WIRES

B AND C

WIRES

B AND C

FACTORY HARNESS

(CUT FROM COIL)

MAGNETIC PICKUP

(NOT USED)

HEAVY RED

HEAVY BLACK

TO BATTERY

IGNITION

DIGITAL-6

PN 6520

PROGRAMMABLE

2 STAGE REV-LIMITER

STEP RETARD

CAPACITIVE DISCHARGE

IGNITION

Plus

NOTE: MSD offers a direct plug in harness that

makes this a splice free installation.

Harness PN 8877 - 1996-on GM Vehicles.

GM IGNITIONS Wiring the 1996 and up single connector coil without harness.

NOTE: The coil connector is labeled A-B-C. The wire in the

A port is positive (pink). The wires in B and C are coil

negative wires, color will vary by application.

NOTE: MSD offers a direct plug in harness that

makes this a splice free installation.

Harness PN 8876 - GM Dual Connector Coils.

Summary of Contents for 6520

























Search results

Summary of Contents for 6520

Reviews:

Related manuals for 6520

Brands by name

Popular brands

MSD 6520, Installation Instruction

Search results

Summary of Contents for 6520

Reviews:

Related manuals for 6520

Brands by name

Popular brands