MSD Ignition 8485 Installation Instructions And Operators Manual Download Page 7 | Manualshive

Page: 7 / 8

background image

INSTALLATION INSTRUCTIONS

7

AUTOTRONIC CONTROLS CORPORATION

• 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

WIRING

The MSD Billet VW Distributor must be used with and MSD Ignition Control. Figure
9 shows the correct wiring of the ignition system.

Figure 9 Wiring the Billet Distributor.

TECH NOTES

_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________

«
...
5
6
7
8
»

Summary of Contents for 8485









Reviews:

No comments

Related manuals for 8485

Brand: ABB Pages: 14

Brand: CAB Pages: 10

Brand: Hamax Pages: 74

Brand: Acdeos Pages: 38

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: Danfoss Pages: 14

Odyssey II Series

Brand: Dakota Digital Pages: 3

Brand: EarthX Pages: 17

Brand: EarthX Pages: 23

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: UltraGauge Pages: 55

Brand: Xerox Pages: 2

Brand: Abicor Binzel Pages: 44

Brand: SRC Pages: 5

Brand: Eiko Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands