background image

AUTOTRONIC CONTROLS CORPORATION

 • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

Limited Warranty

A

utotronic Controls Corporation warrants MSD Ignition products to be free from defects in material

and workmanship under normal use and if properly installed for a period of one year from date of
purchase.  If found to be defective as mentioned above, it will be replaced or repaired if returned prepaid
along with proof of date of purchase.  This shall constitute the sole remedy of the purchaser and the sole
liability of Autotronic Controls Corporation.  To the extent permitted by law, the foregoing is exclusive
and in lieu of all other warranties or representations whether expressed or implied, including any implied
warranty of merchantability or fitness.  In no event shall Autotronic Controls Corporation be liable for
special or consequential damages.

Service

In case of malfunction, this MSD component will be repaired free of charge according to the terms

of the warranty.  When returning MSD components for service, Proof of Purchase must be supplied for
warranty verification.  After the warranty period has expired, repair service is charged based on a minimum
and maximum charge.

Send the unit prepaid with proof of purchase to the attention of:  

Customer Service Department,

Autotronic Controls Corporation, 1490 Henry Brennan Drive, El Paso, Texas 79936

.

When returning the unit for repair, leave all wires at the length in which you have them installed.

Cutting wires close to the unit will void your warranty.  Be sure to include a detailed account of any
problems experienced, and what components and accessories are installed on the vehicle.

The repaired unit will be returned as soon as possible after receipt, COD for any charges.  For more

information, call the MSD Customer Service Line (915) 855-7123.  MSD technicians are available from
8:00 a.m. to 5:00 p.m. Monday - Friday (mountain time).

FRM11992

REVISED 01/95

PRINTED IN U.S.A.

TECH NOTES

_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________

Summary of Contents for 8485









Reviews: