background image

ULTRA ELITE FACEPIECE

CLEANING AND DISINFECTING

Depending on the cleaning policy adopted, either a desig-
nated person or the user should clean each device after
each use. ANSI standards suggest that users should be
trained in the cleaning procedure. Confidence Plus
Cleaning Solution (P/N 10009971) from MSA is recom-
mended. It cleans and disinfects in one operation. It
retains its germicidal efficiency in hard water to inhibit the
growth of bacteria. It will not deteriorate rubber, plastic,
glass, or metal parts. Refer to label for user instructions.

DO NOT use any cleaning substances that can or
might attack any part of the apparatus.

Alcohol should not be used as a germicide
because it may deteriorate rubber parts.

If not rinsed thoroughly, cleaning agent residue
may irritate the wearer’s skin.

1. Preparing Solution

a. Follow the instructions with the Confidence Plus

Cleaning Solution.

b. If the Confidence Plus Cleaning Solution is not

used, wash in a mild cleaning solution, rinse thor-
oughly, and submerge in a germicide solution for
the manufacturer’s recommended time.

2. Clean and Disinfect the Facepiece

a. Remove the mask mounted regulator from the face-

piece.

b. Unthread the thumb screw of NightFighter Heads-

Up Display System receiver Voicemitter Assembly,
slide the receiver from facepiece bracket.

c. Thoroughly wash the facepiece (and nosecup) in the

cleaning solution. A soft brush or sponge can be
used to clean the soiled facepiece.

d. Rinse the facepiece and components in clean,

warm (110°F) water (preferably running and
drained).

e. Clean the pressure-demand exhalation valve by

pressing in on the stem with a blunt object and
flushing with clean water.

f. Allow the facepiece to air dry. Do not dry the parts

by placing them near a heater or in direct sunlight.
The rubber will deteriorate.

g. Operate the exhalation valve by hand to be sure it

works properly.

Note:

Do not force-dry the parts by placing them in a

heater or in direct sunlight. The rubber will deteriorate.
When the facepiece is thoroughly dry, store the facepiece
in the plastic bag that it was shipped in.

3. In general, only the facepiece requires cleaning and

disinfecting after each use.

4. Re-attach NightFighter Heads-Up Display System

Receiver and Voicemitter Assembly.

a. Slide receiver onto facepiece bracket.

b. Finger-tighten thumb screw.

5. Thoroughly dry the facepiece and regulator after

cleaning and disinfecting. The facepiece can trap
water, which could enter the regulator.

REMOVING THE SPEED-ON

®

HEAD HARNESS

1. To remove a damaged SpeeD-ON Head Harness from

the facepiece, lay the facepiece on a table or other flat
surface.

2. To remove a damaged rubber head strap from the

facepiece, lay the facepiece on a table or other flat
surface.

a. Grasp the facepiece lug with the thumb and forefin-

ger of one hand. Grasp the headstrap metal buckle
with the thumb and forefinger of the other hand.

b. Lift the metal buckle up with your thumb as you

stretch the facepiece lug.

c. Turn the facepiece and switch hands to pry up on

the other side of the metal buckle.

d. Pull the facepiece lug out of the metal buckle.
e. Repeat steps a through d for each remaining strap

surface.

3. To remove the bottom buckles, pull the back of the

buckle away from the rubber strap and pull slightly so
the rubber harness end-tab is at the buckle.

4. Fold the end-tab sides together, then slide each tab

through its buckle.

5. Repeat steps 3 and 4 for the other buckle.

CLEANING SPEED-ON HEAD HARNESS

Machine wash in warm water (maximum 120°F) with a
mild detergent. Hang the harness in an open area to air-
dry. Do not dry clean. Do not bleach or use abrasive
cleaners. Do not fold or store when wet.

INSTALLING THE SPEED-ON HEAD HARNESS

1. Install the harness strap buckles on the facepiece rub-

ber lug at the crown and temple locations:

a. Insert the long tab end of the rubber lug into the

metal ring.

b. Pull the entire

rubber lug
through the
metal ring.

5

TAL 805 (L) Rev. 4 - 10042830

Summary of Contents for FireHawk Ultra Elite 10048813















Reviews: