background image

ULTRA ELITE FACEPIECE

iv. There is no loose play in the assembly of parts.

4. For Firehawk slide-to-connect facepieces.

a. Thread the adapter into the facepiece.
b. Tighten the adapter hand tight. Use the component

housing cover to continue to tighten until the top
flat on the octagon is horizontal.

c. Insert the tab on the component housing cover into

the slot in the lens ring.

d. Press in on the front of the cover until the cover

hook snaps in place.

e. Place the neckstrap brackets in the cover sockets.
f. Install and tighten the Phillips screws.
g. Verify that there is no loose play in the assembly of

parts.

5. For Firehawk push-to-connect (PTC) facepieces:

a. Insert the component housing cover tab into the

lens ring slot, leave the cover loose.

b. Place the PTC adapter through the facepiece com-

ponent housing cover and thread the adapter
assembly into the facepiece hand tight.

c. Continue to tighten until the top flat of the adapter

octagon is horizontal.

Note:

The octagon flats on the facepiece adapter must

align with octagon flats of component housing.

d. Press in on the front of the cover until the cover

hook snaps into place.

e. Place the neckstrap brackets into the cover sock-

ets.

f. Install the phillips screws and tighten.
g. Verify that there is no loose play in the assembly of

parts.

6. Don the facepiece and check the face-to-facepiece

seal. Follow the facepiece fit check procedures in the
user’s instructions.

Note:

For questions regarding this procedure, please

contact MSA Customer Service at 1-877-MSA-3473.

12

TAL 805 (L) Rev. 4 - 10042830

Facepiece Components

Firehawk Push-to-Connect

Adapter and Component Housing

Cover

Firehawk Slide-to-Connect

Adapter and Component Housing

Cover

Air Purifying and Pressure Demand

(Except MMR and Firehawk)

Adapter and Component

Housing Cover

Component Housing Cover

Removal Not Necessary

Screws

Locking Ring

Spacers

Gasket (Valve Spider)

Inlet Disc Valve

Neckstrap

MMR Component Housing Cover

MMR Adapter

Facepiece

Summary of Contents for FireHawk Ultra Elite 10048813















Reviews: