MR TAPCON 250 Page 177 Operating Instructions Manual Download

Page: 177 / 216

11 Fault elimination

Maschinenfabrik Reinhausen GmbH 2022

177

8595028/00 EN

TAPCON

250

11.7 Tap position capture incorrect

Characteristics/details

Cause

Remedy

Position indicator incorrect.

▪ Leading sign incorrect.

Incorrect wiring.

Check wiring.

Connect as shown in the connection diagram.

Minimum value of the analog in-
put signal not configured cor-
rectly.

Check parameters.

Minimum value of the analog in-
put signal not configured cor-
rectly.

Check parameters.

Faulty tap position table.

Check the tap position table.

Position indicator incorrect.

▪ Display fluctuates.

Interference.

Shield the line.

Increase the distance from the source of inter-
ference.

Lay interference lines separately.

Route the signal in separate lines (filter,
shielded lines).

No position indicator.

▪ "- -" is displayed.

No measurement signal.

No L- for digital input.

Connect the signal as shown in the connection
diagram.

Check wiring.

Connect as shown in the connection diagram.

Check parameters and activated signals.

Tap position capture over resistor
contact series faulty.

Faulty calibration.

Calibrate the tap position capture over resistor
contact series.

Modified contact resistance val-
ues of the resistor contact series
(e.g. due to weather or age).

Calibrate the tap position capture over resistor
contact series.

Table 55: Tap position capture

11.8 Other faults

If you cannot resolve a problem, please contact Maschinenfabrik Rein-
hausen. Please have the following data ready:

▪ Serial number

– Nameplate

– Info screen

▪ Software version

Summary of Contents for TAPCON 250

























































































































































































































Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands

MR TAPCON 250, Operating Instructions Manual

Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands