MQ Power WHISPERWELD DAW-500S Parts And Operation Manual Download Page 14

Page: 14 / 142

PAGE 14 —DAW-500S WELDER/A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #0 (07/19/01)

DAW-500S — CONTROLS AND INDICATORS

15. Fuel Drain Plug –

Remove this plug to drain fuel from the

fuel tank.

16. Frame Ground Lug –

Connect a ground strap between

this lug and a ground rod. Make sure the ground rod is
inserted deep into the ground to provide a good earth
ground. Consult with local Electrical and Safety Codes for
proper connection.

17. Oil Filter –

Provides oil filtering for the engine.

18. Ignition Switch –

With key inserted turn clockwise to start

engine.

19. Hour Meter –

Indicates number of hours machine has

been in use or hours engine was run.

20. Circuit Protector Circuit Breaker –

This single pole circuit

breaker provides circuit protection (120V @20 amps) for
the G.F.C.I. receptacle.

21. Receptacle G.F.C.I. –

This receptacle provides 120 volts

output at 20 amps.

22. Receptacle –

Provides 120 volts output at 25 amps.

23. Welding Output Terminals –

Connect the welding cable

to this terminal. Select the appropriate polarities according
to the application. See Table 7.

Low Oil Pressure

High Water Temperature

Electrical System Is Not Charging Properly

Preheat Indicator

27. Sub-Selector Switch-

This switch is used to select type of

welding and welding voltage needed. This switch will not
work in CC mode.

28. DC Voltmeter-

Indicated the amount of voltage used during

welding in CV mode.

29. DC Ammeter-

Indicates the amount of amperage being

used during welding in CC mode.

30. Idle Control Switch –

Regulates the engine speed when

the welder/AC generator is under load.

31. Warning Lamp Display –

Lights red when the following

conditions occur:

Figure 3. Controls and Indicators (con't)

24. Main Circuit Breaker –

This single-pole circuit breaker

provides circuit protection (125V @25 amps) for the electric
parts assembly.

25. Current Control (CC) Voltage Control (CV) Adjustment

Knobs –

Use these controls to adjust welding current and

voltage.

26. Welding Type (Wire/Stick) Selector Switch (CV/CC) –

Turn this selector switch to either the CV or CC for welding.

DO NOT

turn this switch under load.

Summary of Contents for WHISPERWELD DAW-500S















































































































































Search results

Summary of Contents for WHISPERWELD DAW-500S

Reviews:

Related manuals for WHISPERWELD DAW-500S

Brands by name

Popular brands

MQ Power WHISPERWELD DAW-500S, Parts And Operation Manual

Search results

Summary of Contents for WHISPERWELD DAW-500S

Reviews:

Related manuals for WHISPERWELD DAW-500S

Brands by name

Popular brands