MQ Multiquip MVH208GH Operation And Parts Manual Download Page 14

Page: 14 / 82

MVH208GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (07/29/16)— PAGE 15

Figure 2 shows the location of the basic controls and

components of the MVH208GH Plate Compactor. The

function of each control is described below:
1.

Rubber Cover

— Lift this rubber cover to gain access

to the fuel tank.

Hour/Tachometer

— Displays the cumulative time

that the machine has been in use. During operation it

displays the rpm reading.

Handle Bar Height Adjuster

— Adjusts the handle

bar to the desired height by loosening the wing nut and

turning the grip clockwise to raise the handle bar and

counterclockwise to lower the handle bar.

Breather Plug

— Allow pressure to escape to the air

in the form of a gas from heat.

Hydraulic Pump (Oil Reservoir)

— Regulates

hydraulic oil flow produced by the direction of the

control lever.

Hand Grip

— When operating the compactor use this

hand grip to maneuver the compactor.

Lifting Bale

— When lifting of the compactor is

required either by forklift, crane etc., tie rope or chain

around this lifting point.

Vibrating Plate

— A flat, open plate made of durable

cast iron construction used in the compacting of soil.

Handle Bar

— When operating the compactor, this

handle is to be in the downward position. When the

compactor is to be

stored

, move the handle bar to

the upright position.

10.

Direction Control Lever

—

Push

the lever forward to

move compactor in a forward direction.

Pull

the lever

backwards to move compactor in backwards direction.

Placing the lever in the middle (midway) will cause the

compactor not to move (neutral).

11.

Throttle Lever

—

Controls speed of the plate

compactor. Place straight vertically to start,

push

fully

counterclockwise for full throttle and fully clockwise to

stop plate compactor.

12.

Vibration Case Oil Filler

— Used to add oil to the

vibration case.

13.

Engine

— This plate compactor uses a GX240UT2SMXC

gasoline engine. Refer to the owner’s manual for

engine information.

14.

Engine ON-OFF Switch

— Used to turn the engine

on or off.

COMPONENTS

Discount-Equipment.com

Summary of Contents for MVH208GH



















































































Search results

Summary of Contents for MVH208GH

Reviews:

Related manuals for MVH208GH

Brands by name

Popular brands

MQ Multiquip MVH208GH, Operation And Parts Manual

Search results

Summary of Contents for MVH208GH

Reviews:

Related manuals for MVH208GH

Brands by name

Popular brands