MPPT M32-10 User Manual Download Page 9

WARNING: 

When  the  power  of  PV  module  is  greater  than  the  rated 

charging power, and the maximum open-circuit voltage of PV array is more 
than100V (at the lowest environmental temperature), the controller may be 
damaged.

 

According to “Peak 

Sun Hours 

diagram”, if the power of PV array exceeds the rated 

charging  power  of  controller,  then  the  charging  time  as  per  the  rated  power  will  be 
prolonged, so that more energy can be obtained for charging the battery. However, in 
the practical application, the maximum power of PV array shall be not greater than 1.5 
x the rated charging power of controller. If the maximum power of PV array exceeds 
the rated charging power of controller too much, it will not only cause the waste of PV 
modules, but also increase the open-circuit voltage of PV array due to the influence of 
environmental  temperature,  which  may  make  the  probability  of  damage  to  the 
controller rise. Therefore, it is very important to configure the system reasonably. For 
the recommended maximum power of PV array for this controller, please refer to the 
table below: 

Model 

Rated Charge 

Current   

Rated Charge 

Power 

Max. PV Array 

Power   

Max. PV open 

circuit voltage 

M32-10 

10A 

130W/12V 
260W/24V 

195W/12V 
390W/24V 

92V

 

100V

 

M32-20 

20A 

260W/12V 
520W/24V 

390W/12V 
780W/24V 

M32-30 

30A 

390W/12V 
780W/24V 

580W/12V 

1170W/24V 

M32-40 

40A 

520W/12V 

1040W/24V 

780W/12V 

1560W/24V 

At 25

 environment temperature   

At minimum operating environment temperature 

2.3Wire Size 

The wiring and installation methods must conform to all national and local electrical 
code requirements. 

 

PV Wire Size 

Since  PV  array  output  varies  due  to  the  PV  module  size,  connection  method  or 
sunlight  angle,  the  minimum  wire  size  can  be  calculated  by  the  Isc

  of  PV  array. 

Please  refer  to  the  value  of  Isc  in  the  PV  module  specification.  When  PV  modules 
connect in series, the Isc is equal to a PV modules Isc. When PV modules connect in 
parallel, the Isc is equal to the sum of Isc of the PV modules. The Isc of the PV array 
must  not  exceed  the  maximum  PV  input  current  of  controllers.  Please  refer  to  the 
table as below: 

NOTE: All PV modules in a given array are assumed to be identical. 

Isc=short circuit current(amps) Voc=open circuit voltage. 

Model 

Max. PV input current 

Max. PV wire size

 

Summary of Contents for M32-10









































Reviews: