MPM MPM-50-PX-51 Operation Manual Download Page 4

 

 

Do  not  disconnect  the  plug  from  the  socket  drawing  the 
power cable. 

 

The power cable may not touch the hot surface. 

 

Do not start the device if the power cable is damaged. 

 

The  replacement  of  the  damaged  power  cable  may  be 
performed  by  the  manufacturer;  the  service  maintenance 
shall be performed by the qualified technician. 

 

The hood shall be cleaned both inside and outside, at least 
monthly,  or  every  35  hours  of  hood  operation.  Each  time, 
before  the  hood  cleaning,  the  hood  shall  be  disconnected 
from the power (disconnect the power cable plug or turn off 
the safety levers). 

 

The device may be used by the children in the age of at least 
8  years,  and  by  the  persons  with  limited  physical,  mental 
abilities, or by persons with a lack of experience in device 
operation,  provided  that  the  due  supervision  or  training  in 
terms of the safe device operation was ensured, in order to 
make clear all the related risks. 

 

The children shall not play with the device. 

 

The children without the supervision shall not perform the 
device cleaning and maintenance. 

 

The device is market according to European Union Directive 
2002/96/EU,  about  the  electric  and  electronic  equipment 
(WEEE).  Ensuring  the  correct  disposal  of  the  device,  you 
will  help  to  limit  the  risks  of  a  negative  impact  over  the 
environment and health. 

 

 

NOTE:

 

The accessible parts may become hot in course of the cooking range 
operation.  The  use  of  screws  or  other  fastening  elements  with 
violation  of  the  Manual  requirements,  may  cause  the  electrical 
shock. 

Summary of Contents for MPM-50-PX-51





















Reviews: