background image

13

USING THE APPLIANCE

Important:
NEVER USE THE BEATERS OR
KNEADERS AT THE SAME TIME AS THE
BLENDER SHAFT, MINI-CHOPPER OR
BLENDER BOWL.

MIXER FUNCTION WITH BEATERS
OR KNEADERS:

• Manual use:

• Check that the appliance is

unplugged, that the speed control

(a2)

is set to 

"0"

and that there is

neither blender shaft, nor mini-
chopper nor blender connected to
the back of the appliance.

• Insert the rods of each beater 

(b)

or kneader 

(d)

into the

corresponding holes and lock into
place. 

The beaters and kneaders

have a specific shape. The
kneader or beater equipped with
the metal collar (f) should be
positioned to the left into the
biggest hole (Fig. 1).

• Connect the appliance: 

- Your appliance has 5 speed

levels and a turbo button. Always
begin mixing or kneading at
speed 1 initially, then move to
speed 2, 3, 4 or 5 (Fig. 2).

- To knead thick dough, we

recommend using speed 

only.

- You can also increase the speed

by pressing the turbo button. We
however recommend that you use
it only briefly (a maximum of 30
seconds for thick dough).

• After finishing, set the speed control

(a2) 

to 

"0"

.

• Disconnect.
• Then press the ejection button

(a1)

to remove the beaters or kneaders.

• Using with the base (g):

(depending on model)

• Check that the appliance is

unplugged, that the speed control

(a2)

is set to 

"0"

and that there is

no blender shaft.

• Insert the rods of each beater 

(c)

or kneader

(e)

into the

corresponding holes and lock into
place. 

The beaters and kneaders

have a specific shape. The
kneader or beater with the metal
collar (f)

should be positioned to

the left, in the biggest hole

(Fig. 1).

• Place the base 

(g)

on the worktop:

- To raise the arm, unlock by

pressing the button

(i) (Fig. 3).

- Position the bowl 

(h) (Fig. 3).

- Press the button 

(i) to unlock the

arm and lower it (Fig. 4).

- Place the mixer fitted with the

kneaders or beaters on the
hinged arm until you hear it click
into place 

(Fig. 5).

Note:
INSERT THE MIXER BY POSITIONING
THE BEATERS OR KNEADERS IN THE
NOTCHES (Fig. 5).

• Connect the appliance:

- Your appliance has 5 speed levels

Summary of Contents for HM6151



















Reviews: