MOULDPRO Flosense 4.0 Installation & User Manual Download Page 27

Page: 27 / 28

P a g e

User Guidelines

– Flosense 4.0 Manifold 16-06-2020

Version 002

7. Insert the sensor gently in the piping.

8. When the sensor is placed vertically, it

can be pushed down into the piping

9. Push the locking pin back in. It may be

challenging if it has been pulled out too
far in steps 2 and 3

10. Push the locking pin all the way in. You

will know that it is all the way in, when it
is within the small gap of the hook on the
piping.

4.4.

Cleaning the system

All surfaces shall be cleaned with a piece of cloth soaked in soap water or any other non-

corrosive cleaning agent, concerned steel and brass.

Furthermore, we recommend descaling the system by using Mouldpro Remover Plus

Powder Descaling Agent.

Find more information on

www.mouldpro.com

Summary of Contents for Flosense 4.0





























Search results

Summary of Contents for Flosense 4.0

Reviews:

Related manuals for Flosense 4.0

Brands by name

Popular brands

MOULDPRO Flosense 4.0, Installation & User Manual

Search results

Summary of Contents for Flosense 4.0

Reviews:

Related manuals for Flosense 4.0

Brands by name

Popular brands