manualshive.com logo in svg

Motorola Vanguard 100, User Manual

Share
Download
Motorola Vanguard 100 User Manual Download Page 78

3-28 

Configuring a Vanguard Router

Configure LAN Connections  

Note

There are four additional RTP/UDP/IP Header Compression DEBUG 
parameters. Unless you are a thoroughly experienced network professional, 
operating in the DEBUG Mode is not recommended. Please contact your 
Motorola Service Representative for additional information.

Number of Session to be Compressed

Default

255

Range

1 to 1024

Description

Specifies the number of session to be compressed. Changes to this 
parameter causes the context list to be refreshed.

Each compression session that exists between the compressor and 
decompressor is uniquely identified by a session context identifier 
(CID). The CID can be 8 or 16 bit. When the configured value 
exceeds 255, a 16 bit CID. 

Full Header Refresh Counter

Default

0

Range

0 to 1000

Description

A setting of 0 indicates that there is no periodic transfer. A setting 
of 1 to 1000 indicates the number of compressed packet 
transmitted before a FULL HEADER packet is retransmitted.

Summary of Contents for Vanguard 100































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands