manualshive.com logo in svg

Motorola Vanguard 100, User Manual

Share
Download
Motorola Vanguard 100 User Manual Download Page 60

3-10 

Configuring a Vanguard Router

Configure LAN Connections  

LAN Connection Parameters Menu

Introduction

Use the LAN Connection Parameters menu to configure the number of LAN 
Connections. The maximum number of configurable LAN Connections is 254. 
These can be both Router Interfaces and Bridge links. 

Note that since four Bridge links are assigned for LAN Bridge links, the number of 
WAN Bridge Links supported is 250.

What You See in 
This Record

Figure 3-5 shows the LAN Connection Parameters menu.

Figure 3-5. LAN Connection Parameters Menu

Parameter

The Maximum Number of LAN Connections parameter is described below:

*Maximum Number of LAN Connections

Node: Address: 

Date: 

Time: 

Menu: Configure LAN Connections 

Path: 

1.

LAN Connection Parameters

Range:

32 to 2000 (depends on the product)

Default:

32

Description: Specifies the configurable number of LAN Connections. 

Connections are either Router Interfaces or Bridge links.

Summary of Contents for Vanguard 100































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands