Motorola SE-1010, Product Manual

Page: 15 / 41

Document Number: 504834-001 9
CC/LOG PORT FORM_C OUT ETHERNET DHEI OUT ASI OUT ASI MON DS3 OUT
DIGITAL
AUDIO IN A
DIGITAL
AUDIO IN B
DIGITA L VIDEO
LOOP THRU
DIGITAL
VIDEO IN
ANALOG AUDIO A IN
L+ L- GND R+ R-
ANALOG AUDIO B IN
L+ L- GND R+ R-
ANALOG VIDEO
LOOP THRU
ANALOG
VIDEO IN
Form_C Out
CC/Log Port
Ethernet
DHEI Out
ASI DS3 Digital
Audio
Digital
Video
Analog
Video
Analog
Audio
COM NC NO
AC
Power
SE Encoder Factory Presets
Table 1 shows the encoder’s 30 factory-defined presets. To restore the presets to their default
settings, see “Reset Menu” on page 26.
Table 1 Default Settings For Factory-defined Presets
Presets
Menu : Option
1 2 3 4 5 6 7
8
−
30
Video : In NTSC 525SD I NTSC 525SD I NTSC 525SD I NTSC 525SD I
Video : Res 528 x 480 528 x 480 352 x 480 352 x 480 704 x 480 704 x 480 704 x 480 704 x 480
Video : Rate 4.00 Mbps 4.00 Mbps 3.00 Mbps 3.00 Mbps 5.00 Mbps 5.00 Mbps 8.00 Mbps 8.00 Mbps
Video : GOP (Length) 15 15 15 15 15 15 15 15
Video : Film On On On On On On On On
Video : Aspect 4:3 4:3 4:3 4:3 4:3 4:3 4:3 4:3
Video : Fmt 4:2:0 4:2:0 4:2:0 4:2:0 4:2:0 4:2:0 4:2:0 4:2:0
Audio : Std AC3 AC3 AC3 AC3 AC3 AC3 AC3 AC3
Audio : Mode AN Stereo DG Stereo AN Stereo DG Stereo AN Stereo DG Stereo AN Stereo DG Stereo
Audio : Rate 192 kbps 192 kbps 192 kbps 192 kbps 256 kbps 256 kbps 256 kbps 256 kbps
Audio1 : Language eng eng eng eng eng eng eng eng
Audio2 : Language eng eng eng eng eng eng eng eng
Audio : DialNorm -31 dB -31 dB -31 dB -31 dB -31 dB -31 dB -31 dB -31 dB
PID : V (Video) 0032 0032 0032 0032 0032 0032 0032 0032
PID : A1 (Audio 1) 0033 0033 0033 0033 0033 0033 0033 0033
PID : A2 (Audio 2) 0034 0034 0034 0034 0034 0034 0034 0034
PID : P (PMT) 0035 0035 0035 0035 0035 0035 0035 0035
PID : W (WST) 0036 0036 0036 0036 0036 0036 0036 0036
PGM 00001 00001 00001 00001 00001 00001 00002 00002
Note: All other parameters are 0, No, or disabled.
Fault and Alarm
The SE encoder provides a Form_C contact closure to trigger alarm equipment. The following
diagram shows the Form_C port on the left of the back panel. To view the error messages that
will activate the Form_C, see Table A1 on page 28. For Form_C pinouts, see “Connector
Pins” on page 29.