manualshive.com logo in svg

Motorola MPC860 PowerQUICC, User Manual

The Motorola MPC860 PowerQUICC user manual is a comprehensive guide to help you maximize the potential of this powerful product. With clear instructions and detailed diagrams, you can easily set up and operate your device. Download this free manual from manualshive.com to get the most out of your Motorola MPC860 PowerQUICC.

Share
Download
background image

7-2

MPC860 PowerQUICC UserÕs Manual

MOTOROLA

Part II. PowerPC Microprocessor Module

7.1  Exceptions

The OEA deÞnes a set of exceptions for PowerPC processors, some of which are optional.
The following sections describe exceptions implemented on the MPC860. Those deÞned
by the OEA are described in Section 7.1.2, ÒPowerPC-DeÞned Exceptions.Ó Section 7.1.3,
ÒImplementation-SpeciÞc Exceptions,Ó describes implementation-speciÞc exceptions.

All exceptions associated with memory are implemented as precise, which means that a
load/store instruction is not complete until all possible error indications are sampled from
the load/store bus. This also implies that a store or nonspeculative load instruction is not
issued to the load/store bus until all previous instructions have completed. If a late error
occurs, a store cycle (or a nonspeculative load cycle) can be issued and aborted.

In each exception handler, when registers SRR0 and SRR1 are saved, MSR[RI] can be set.

Table 7-1 deÞnes the offset value by exception type and the sections that follow describe
each exception in detail. Note that the base is determined by the setting of MSR[IP].

Table 7-1. Offset of First Instruction by Exception Type   

Offset

Exception Description

OEA-DeÞned Exceptions 

0x00000

Reserved

Ñ

0x00100

System reset interrupt

See Section 7.1.2.1, ÒSystem Reset Interrupt (0x00100).Ó

0x00200

Machine check interrupt

See Section 7.1.2.2, ÒMachine Check Interrupt (0x00200).Ó

0x00300

DSI

A DSI exception is never generated by hardware, but software may 
branch to this location because of an data TLB error or miss exception. 
See Section 7.1.2.3, ÒDSI Exception (0x00300).Ó

0x00400

ISI

An ISI exception is never generated by the hardware, but software may 
branch to this location because of an implementation-speciÞc instruction 
TLB error exception. See Section 7.1.2.4, ÒISI Exception (0x00400).Ó

0x00500

External Interrupt

See Section 7.1.2.5, ÒExternal Interrupt Exception (0x00500).Ó

0x00600

Alignment

Alignment exceptions result from the following conditions:

¥ The operand of a load/store multiple is not word-aligned.
¥ The operand of a 

lwarx

 or 

stwcx. 

is not word-aligned.

¥ The operand of a load/store instruction is not naturally aligned when 

MSR[LE]

 

= 1.

¥ Trying to execute a multiple/string instruction when MSR[LE]

 

= 1.

See Section 7.1.2.3, ÒDSI Exception (0x00300).Ó

0x00700

Program

The MPC860 cannot generate a ßoating-point exception type exception. 
See Section 7.1.2.7, ÒProgram Exception (0x00700).Ó An 
implementation-speciÞc software emulation exception is generated 
instead of an illegal instruction type program exception. A privileged 
instruction program exception is generated for an on-core valid SPR Þeld 
or any SPR encoded as an external SPR if SPR[0] = 1 and MSR[PR] = 
1, as well as for attempts to execute supervisor-level instructions when 
MSR[PR]

 

= 1. See Table 6-11.

Summary of Contents for MPC860 PowerQUICC



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC860 PowerQUICC

S&C 6800 Series Instruction Sheet preview
6800 Series
Brand: S&C Pages: 40
ZKTeco SC800 User Manual preview
SC800
Brand: ZKTeco Pages: 123
Vacon NX series Maintenance Manual preview
NX series
Brand: Vacon Pages: 64
ZKTeco F6 Installation Manual preview
F6
Brand: ZKTeco Pages: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Brand: FASAR ELETTRONICA Pages: 2
Faro 33928 Installation Manual preview
33928
Brand: Faro Pages: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Brand: YASKAWA Pages: 456
hager coviva Smartbox TKP100A Quick Manual preview
coviva Smartbox TKP100A
Brand: hager Pages: 4
Vag ZETA Operating And Maintenance Instructions Manual preview
ZETA
Brand: Vag Pages: 12
IDTECK iTDC Troubleshooting Manual preview
iTDC
Brand: IDTECK Pages: 94
Valcom V-2000 Manual preview
V-2000
Brand: Valcom Pages: 6
B&G ZEUS S Detailed App Manual preview
ZEUS S
Brand: B&G Pages: 19
EFI E-42 Installation And Service Manual preview
E-42
Brand: EFI Pages: 127
maxxess eMAX-EP4502 Installation Manual preview
eMAX-EP4502
Brand: maxxess Pages: 11
SOLARJACK PVA 5-30 User Manual preview
PVA 5-30
Brand: SOLARJACK Pages: 14
ATT Holding Kade KZ-700-U/H Installation Manual preview
Kade KZ-700-U/H
Brand: ATT Holding Pages: 12
Digital View ALR-1920-120 Instructions Manual preview
ALR-1920-120
Brand: Digital View Pages: 35
National Instruments cRIO-9037 Getting Started Manual preview
cRIO-9037
Brand: National Instruments Pages: 20

Brands by name

Popular brands

Load more brands