109
Ethernet Tx Packets:
This displays the total number of good packets the bridge has sent for
transmission by the local Ethernet interface. . See note
1081H
19.
Ethernet Rx Packets:
This displays the total number of good packets the bridge has
received from the local Ethernet interface. . See note See note
1082H
19.
Packets To Internal Stack:
This displays the total number of good packets the bridge has
transmitted to the internal stack (e.g., ARP requests, PING requests, HTTP requests). See
note
1083H
19.
Packets From Internal Stack
: This displays the total number of good packets the bridge has
received from the internal stack (e.g. ARP responses, PING replies, HTTP responses). See
note
1084H
19.
Transmit Data Rate:
The data rate in the transmit direction, expressed in Mbps and
presented as: max, mean, min, and latest histogram format. The max, min and latest are true
instantaneous measurements; the mean is the mean of a set of one second means. See Note
1085H
14. Expected data rates can be found in Section
1086H
6.1.5.
Receive Data Rate:
The data rate in the receive direction, expressed in Mbps and presented
as: max, mean, min, and latest histogram format. The max, min and latest are true
instantaneous measurements; the mean is the mean of a set of one second means. . See
Note
1087H
14. Expected data rates can be found in Section
1088H
6.1.5.
Aggregate Data Rate:
The sum of the data rate in the directions expressed in Mbps and
presented as: max, mean, min, and latest histogram format. The max, min and latest are true
instantaneous measurements; the mean is the mean of a set of one second means. See Note
1089H
14. Expected data rates can be found in Section
1090H
6.1.5.
Link Capacity:
The maximum aggregate data capacity available for user traffic under the
current radio link conditions, assuming the units have been connected using Gigabit Ethernet.
The sum of the displayed Transmit and Receive data rates may be lower than this figure if the
link isn't fully loaded by the current traffic profile.
Transmit Modulation Mode:
The modulation mode currently being used on the transmit
channel. The number in brackets after the modulation mode and coding rate string is the
effective data rate available to all MAC layer protocols. Details on the modulation modes can
be found in Section
1091H
23.1 “System Specifications”.
Summary of Contents for MOTOWI 4 PTP 600 Series
