background image

 

 

 

 

Label Symbols  

 

SYMBOL 

INDICATES 

 

DC voltage 

 

AC voltage 

 

For indoor use only 

 

Class II equipment 

 

Energy Efficiency Marking 

 

Center-positive power input polarity 

 

FCC Statement 

 

This device complies with Class B Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) this device may not cause harmful interference, and (2) this device must 

accept any interference received, including interference that may cause undesired operation.  
Note: this equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 

uses, and can radiate radio frequency energy and, if not installed and used in accordance with 

the instruations, may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does 

cause harmful interference to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures: reorient or relocate the receiving antenna, increase the 

separation between the equipment and receiver, connect the equipment into an outlet on a 

circuit different from that to which the receiver is connected, and/or consult the dealer or an 

experienced radio/TV technician for help.  

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to operate the equipment. 

 

This transmitter must not be co-located or operating in conjunction with any other antenna or 

transmitter.  For operation within the 5.15 - 5.25GHz frequency range, it is restricted to indoor 

operation. This device meets all the other rerquirements specified in Part 15E, Section 15.407 of 

the FCC Rules. 
FCC Radiation Exposure Statement:  This equipment complies with FCC radiation exposure 

limits set forth for an uncontrolled environment. This equipment should be installed and 

operated within minimum distance 38 cm between the radiator and your body. 

 

MTRLC LLC  PO Box 121147   Boston, MA 02112-1147 

©MTRLC LLC 2020. MOTOROLA and the Stylized M Logo are trademarks or 

registered trademarks of Motorola Trademark Holdings, LLC. and are used under 

license. All other trademarks are the property of their respective owners. All 
rights reserved. 

 

 

 

27797-EL-A

/0950

   

Summary of Contents for ML2410

















Reviews: