manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  2.  ColdFire Core  

2-11

Chapter 2  
ColdFire Core

This chapter provides an overview of the microprocessor core of the MCF5272. The
chapter describes the V2 programming model as it is implemented on the MCF5272. It also
includes a full description of exception handling, data formats, an instruction set summary,
and a table of instruction timings. 

2.1  Features and Enhancements

The MCF5272 is the most highly-integrated V2 standard product, containing a variety of
communications and general-purpose peripherals. The V2 core was designed to maximize
code density and performance while minimizing die area.

The following list summarizes MCF5272 features:

•

Variable-length RISC Version 2 microprocessor core

•

Two independent, decoupled pipelines—two-stage instruction fetch pipeline (IFP) 
and two-stage operand execution pipeline (OEP)

•

Three longword FIFO buffer provides decoupling between the pipelines

•

32-bit internal address bus supporting 4 Gbytes of linear address space

•

32-bit data bus

•

16 user-accessible, 32-bit-wide, general-purpose registers

•

Supervisor/user modes for system protection

•

Vector base register to relocate exception-vector table

•

Optimized for high-level language constructs

2.1.1  Decoupled Pipelines

The IFP prefetches instructions. The OEP decodes instructions, fetches required operands,
then executes the specified function. The two independent, decoupled pipeline structures
maximize performance while minimizing core size. Pipeline stages are shown in Figure 2-1
and are summarized as follows:

•

Two-stage IFP (plus optional instruction buffer stage)

— Instruction address generation (IAG) calculates the next prefetch address.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Cypress Semiconductor CY7C1034DV33 Specification Sheet preview
CY7C1034DV33
Brand: Cypress Semiconductor Pages: 9
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
OpenVox B800P User Manual preview
B800P
Brand: OpenVox Pages: 13
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Brand: ZALMAN Pages: 9
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Nakayo NYC-16VDSL-B Instruction & Installation Manual preview
NYC-16VDSL-B
Brand: Nakayo Pages: 119
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
LevelOne GSW-0890 Quick Installation Manual preview
GSW-0890
Brand: LevelOne Pages: 4
HighPoint SSD7202 Quick Installation Manual preview
SSD7202
Brand: HighPoint Pages: 12
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Brand: ekwb Pages: 3
Robotis OpenCM 485 Manual preview
OpenCM 485
Brand: Robotis Pages: 10
StetSom STX2448 User Manual preview
STX2448
Brand: StetSom Pages: 18
Cypress Semiconductor CY7C1480V25 Specification Sheet preview
CY7C1480V25
Brand: Cypress Semiconductor Pages: 32

Brands by name

Popular brands

Load more brands