Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 60 | Manualshive

Page: 60 / 550

background image

2-12

MCF5272 User’s Manual

Features and Enhancements

— Instruction fetch cycle (IC) initiates prefetch on the processor’s local instruction

bus.

— Instruction buffer (IB) optional stage uses FIFO queue to minimize effects of

fetch latency.

•

Two-stage OEP

— Decode, select/operand fetch (DSOC) decodes the instruction and selects the

required components for the effective address calculation, or the operand fetch
cycle.

— Address generation/execute (AGEX) calculates the operand address, or performs

the execution of the instruction.

Figure 2-1. ColdFire Pipeline

2.1.1.1 Instruction Fetch Pipeline (IFP)

The IFP generates instruction addresses and fetches. Because the fetch and execution
pipelines are decoupled by a 3 longword FIFO buffer, the IFP can prefetch instructions
before the OEP needs them, minimizing stalls.

Instruction

Instruction

FIFO

Decode & Select,

Address

Data[31:0]

IAG

IC

IB

DSOC

AGEX

Address [31:0]

Instruction Buffer

Address

Generation

Fetch Cycle

Generation,

Execute

Operand Fetch

Operand
Execution
Pipeline

Instruction
Fetch
Pipeline

«
...
58
59
60
61
62
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: NXP Semiconductors Pages: 24

CLICK PLUS C2-02CPU

Brand: Automationdirect.com Pages: 10

Brand: MICROENER Pages: 24

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Protection Board R0E330850ACBP0

Brand: Renesas Pages: 8

Hotwire 5620 RTU

Brand: Paradyne Pages: 20

Aeroflow FX 120 VAF-1225

Brand: Vantec Pages: 2

Brand: Digi Pages: 339

Brand: ZALMAN Pages: 6

Brand: IBASE Technology Pages: 49

Brand: Classe Audio Pages: 70

Brand: Me Pages: 28

Brand: VIA Technologies Pages: 2

Brand: Ublox Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands