manualshive.com logo in svg

Motorola Digital DNA MSC8101, Technical Data Manual

Share
Download
Motorola Digital DNA MSC8101 Technical Data Manual Download Page 39

1-35

Communications Processor Module (CPM) Ports

PC25

BRG7O

CLK7

TIN4

DMA: DACK2

Output

Input

Input

Output

Baud-Rate Generator 7 Output
The CPM supports up to 8 BRGs. The BRGs can be used 
internally by the bank-of-clocks selection logic and/or provide 
an output to one of the 8 BRG pins.

Clock 7
The CPM supports up to 10 clock input pins. The clocks are 
sent to the bank-of-clocks selection logic, where they can be 
routed to the controllers.

Timer Input 4
A timer can have one of the following sources: another timer, 
system clock, system clock divided by 16 or a timer input. The 
CPM supports up to 4 timer inputs. The timer inputs can be 
captured on the rising, falling or both edges.

DMA: Data Acknowledge 2
DACK2, DREQ2, DRACK2 and DONE2 belong to the SIU 
DMA. DONE2 and DRACK2 are signals on the same pin and 
therefore cannot be used simultaneously. There are two sets 
of DMA pins associated with the PIO ports.

PC24

BRG8O

CLK8

TIN3

Timer4: TOUT4

DMA: DREQ2

Output

Input

Input

Output

Input

Baud-Rate Generator 8 Output
The CPM supports up to 8 BRGs. The BRGs can be used 
internally by the bank-of-clocks selection logic and/or provide 
an output to one of the 8 BRG pins.

Clock 8
The CPM supports up to 10 clock input pins. The clocks are 
sent to the bank-of-clocks selection logic, where they can be 
routed to the controllers.

Timer Input 3
A timer can have one of the following sources: another timer, 
system clock, system clock divided by 16, or a timer input. 
The CPM supports up to four timer inputs. The timer inputs 
can be captured on the rising, falling, or both edges.

Timer 4: Timer Out 4
The timers (Timer1–4]) can output a signal on a timer output 
(TOUT[1–4]) when the reference value is reached. This signal 
can be an active-low pulse or a toggle of the current output. 
The output can also be connected internally to the input of 
another timer, resulting in a 32-bit timer.

DMA: Data Request 2
DACK2, DREQ2, DRACK2, and DONE2 belong to the SIU 
DMA. DONE2 and DRACK2 are signals on the same pin and 
therefore cannot be used simultaneously. There are two sets 
of DMA pins associated with the PIO ports.

Table 1-5.  Port C Signals (Continued)

Name

Dedicated 

I/O Data

Direction

Description

General-
Purpose 

I/O

Peripheral Controller: 

Dedicated I/O

Protocol

Summary of Contents for Digital DNA MSC8101





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands